1106118721 Kenmore Dryer - Instructions

All Instructions for the 1106118721
46 - 60 of 197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
Wen the dryer gets hot but dry anything when it runs and no air comes through the filter opening with the filter out
2 of 2 people found this instruction helpful.
  • Willis from FORT WORTH, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cab le from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.
Was this helpful?
Thank you for voting!
broken door cables
2 of 2 people found this instruction helpful.
  • Richard from LA BELLE, PA
  • Really Easy
  • 30 - 60 mins
followed directions that came with order confirmation e-mail
Was this helpful?
Thank you for voting!
Door switch would not let dryer operate
2 of 2 people found this instruction helpful.
  • George from Rio Communities, NM
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top bac k out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Was this helpful?
Thank you for voting!
Blower belt broke on my 58 year old Kenmore gas dryer.
2 of 2 people found this instruction helpful.
  • Mary from KENNESAW, GA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Called my son. He took off the back put the belt on and we were ready to go.
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people found this instruction helpful.
  • Susan from WARREN, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people found this instruction helpful.
  • James from Richmond, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people found this instruction helpful.
  • katherine from Salem, OR
  • Easy
  • 15 - 30 mins
  • Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people found this instruction helpful.
  • Charles from Cape Girardeau, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people found this instruction helpful.
  • Laszlo from Vienna, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people found this instruction helpful.
  • Victoria from Roslyn Heights, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people found this instruction helpful.
  • satyavenkata from Bentonville, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
The door cables broke.
1 person found this instruction helpful.
  • Robert from Perris, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I replaced the springs and cables in the dryer door.
Was this helpful?
Thank you for voting!
All Instructions for the 1106118721
46 - 60 of 197