110299 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
I followed the video guide, which was excellent
7 of 7 people
found this instruction helpful.
-
Richard from NAPLES, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this helpful?
Thank you for voting!
Electrical burning smell washer stoped working
11 of 19 people
found this instruction helpful.
-
Arthur from Statesville, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced motor starting capacitor. Noticed water leak at pump and replaced pump
Other Parts Used:
Was this helpful?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
8 of 10 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this helpful?
Thank you for voting!
Lid Switch Screw Mounts Broke
7 of 8 people
found this instruction helpful.
-
Leo from Compton, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I re
... Read more
placed the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.
Read less
Was this helpful?
Thank you for voting!
Ground prong on power cord was broken
10 of 17 people
found this instruction helpful.
-
RONALD from PORT ORCHARD, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Other Parts Used:
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people
found this instruction helpful.
-
Ernestine from CARRIERE, MS
- Really Easy
- 30 - 60 mins
-
Socket set
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Washer would sometimes not go into spin cycle. Opening and closing lid would put it into spin.
7 of 8 people
found this instruction helpful.
-
Donald from Toopeka, KS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Was this helpful?
Thank you for voting!
The wash cycle made a loud grinding noise when it went from filling to wash.
6 of 6 people
found this instruction helpful.
-
Angelo from PORTLAND, ME
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi ... Read more th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi ... Read more th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Read less
Was this helpful?
Thank you for voting!
washer would walk all over when in the spin cycle
6 of 6 people
found this instruction helpful.
-
Chris from Bonners Ferry, ID
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to
... Read more
see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would not run or start when start button was pushed.
6 of 6 people
found this instruction helpful.
-
John from PATERSON, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Based on, online troubleshooting and repair guide. First repair attempt was unsuccessful after replacing suggested parts and required a professional repair tech to diagnose the issue. Second attempt at repair was successful after the proper issue was diagnosed. Sometimes you just have to call a professional. John Suchinsky, Paterson NJ
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would not work in agitate or spin cycle
6 of 6 people
found this instruction helpful.
-
yesenia from apopka, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off wit
... Read more
hout unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Read less
Was this helpful?
Thank you for voting!
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!
washer not draining
8 of 12 people
found this instruction helpful.
-
maria from san Marcos, TX
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench set
but switch fixed
Was this helpful?
Thank you for voting!