110299 Kenmore Washer - Instructions

All Instructions for the 110299
91 - 105 of 1332

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer tub off balance and noisy
9 of 10 people found this instruction helpful.
  • Gregory from Kent, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag e with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Was this helpful?
Thank you for voting!
Wouldn’t drain pump made loud noise
10 of 13 people found this instruction helpful.
  • REED from BUCHANAN, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people found this instruction helpful.
  • Elzoria from FROSTPROOF, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people found this instruction helpful.
  • Craig from Woodland Hills, UT
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!
Severe wobble during spin cycle.
9 of 11 people found this instruction helpful.
  • Steven from Dallas, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Was this helpful?
Thank you for voting!
Direct drive pump was leaking
8 of 8 people found this instruction helpful.
  • Philip from DENTON, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people found this instruction helpful.
  • Delmar from EAST TROY, WI
  • Really Easy
  • 30 - 60 mins
  • Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
Leaking water from bottom after wash
9 of 11 people found this instruction helpful.
  • Robert from Wildomar, CA
  • Easy
  • 30 - 60 mins
Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished
Was this helpful?
Thank you for voting!
Out of balance on spin cycle
9 of 11 people found this instruction helpful.
  • Tom from LATROBE, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.
Was this helpful?
Thank you for voting!
washer would not spin clothes
8 of 8 people found this instruction helpful.
  • Joseph from KEARNY, NJ
  • Really Easy
  • 1- 2 hours
  • Socket set
Followed the video instructions. Had no problems. The video was accurate.
Was this helpful?
Thank you for voting!
noisy
8 of 9 people found this instruction helpful.
  • clinton from selah, WA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
just like video showed really helpfull
Was this helpful?
Thank you for voting!
Spider coupling between motor and transmission broken
9 of 12 people found this instruction helpful.
  • Robert from Friendswood, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep air.
Was this helpful?
Thank you for voting!
banging noise during spin cycle, tub out of balance
8 of 9 people found this instruction helpful.
  • Russell from CHARLTON CITY, MA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people found this instruction helpful.
  • Barbara from RICHMOND, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!
Water Pump was leaking
9 of 13 people found this instruction helpful.
  • Rick from Liberty, SC
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on th e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Was this helpful?
Thank you for voting!
All Instructions for the 110299
91 - 105 of 1332