110299 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!
Washer not agitating
7 of 10 people
found this instruction helpful.
-
Keith from Erie, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I looked for a youtube video on how to repair the lid switch. The video was very good but was filmed in a perfect world. My washer sits in a somewhat confined area so getting the outside skin put back perfectly was a bit tricky.
Was this helpful?
Thank you for voting!
Gear stripped on main spline
6 of 7 people
found this instruction helpful.
-
Bernard from ARIZONA CITY, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this helpful?
Thank you for voting!
loud noise during spin cycle, then not spinning at all
6 of 7 people
found this instruction helpful.
-
William from CHESHIRE, CT
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench set
Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a ... Read more short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new
Thanks!!
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a ... Read more short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new
Thanks!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broken lid switch
6 of 7 people
found this instruction helpful.
-
Gary from Stuart, FL
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I unplugged the machine.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.
Was this helpful?
Thank you for voting!
Loud Screeching noise when draining water
5 of 5 people
found this instruction helpful.
-
Steven from Port Saint Lucie, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to
... Read more
wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.
Read less
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people
found this instruction helpful.
-
Matthew from Wauwatosa, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
heavy loads did not spin dry properly
6 of 8 people
found this instruction helpful.
-
Chet from CLEARWATER, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Other Parts Used:
Was this helpful?
Thank you for voting!
tub would not spin....burning smell
6 of 8 people
found this instruction helpful.
-
John from Elm Mott, AL
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Unplugged washer. Pulled the washer away from the wall & leaned it back against the wall to access the underneath side of the washer. Disconnected water hoses to the pump with water pump pliers. Have drain pan handy to catch the water, approximately 1 qt. Remember which hose goes to the proper place. Removed two retaining screws/st
... Read more
raps allowing the motor to be seperated from the transmission. There is enough slack in the wiring to allow you to drop the motor without disconnecting. You do not need to remove the water pump. Removed old coupling & replaced with the new one. Make sure you use the "new style" replacement coupler or you will be doing this repair again very soon! Schematics are available online.
Read less
Was this helpful?
Thank you for voting!
Coupling on Whirlpool Washer gave out
5 of 5 people
found this instruction helpful.
-
Ronny from Santa Monica, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
The coupling, made of plastic and rubber, on our Whirlpool washer gave out. Done the same repair nine years ago and knew what to do. Here is a short summery:
1. unscrew the 2 screws that hold the control panel on top of the machine in place
2. unscrew the screws that connect the housing with the back panel
... Read more >3. pop the 2 clips under the control panel to release the back panel
4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)
5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine
6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.
7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside
8. you can now remove the broken coupling
9. check for any fragments and clean off what needs to be cleaned
10. replace the coupling
11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!
12. test
1. unscrew the 2 screws that hold the control panel on top of the machine in place
2. unscrew the screws that connect the housing with the back panel
... Read more >3. pop the 2 clips under the control panel to release the back panel
4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)
5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine
6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.
7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside
8. you can now remove the broken coupling
9. check for any fragments and clean off what needs to be cleaned
10. replace the coupling
11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!
12. test
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
1. No hot water and cold water filled very slowly. 2. Washing machine severely vibrated and was very noisy.
5 of 5 people
found this instruction helpful.
-
Janice from BLUE SPRINGS, MO
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
EXACTLY as your video demonstrated.
Other Parts Used:
Was this helpful?
Thank you for voting!
Replacing water inlet valve with new one
5 of 5 people
found this instruction helpful.
-
David from HENRY, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her
... Read more
)
Read less
Was this helpful?
Thank you for voting!
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people
found this instruction helpful.
-
TERRY from WAUKEE, IA
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Read less
Was this helpful?
Thank you for voting!
Washer would not fill with water...
5 of 5 people
found this instruction helpful.
-
Eddie from Charlotte, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered nex
... Read more
t.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
Read less
Was this helpful?
Thank you for voting!
Water was leaking out to floor after each load
6 of 8 people
found this instruction helpful.
-
James from MILWAUKEE, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Replaced the springs after watching the video's from this site and problem has been solved.
Other Parts Used:
Was this helpful?
Thank you for voting!