110299 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking during run cycle
13 of 15 people
found this instruction helpful.
-
michael from weymouth, MA
- Really Easy
- 15 - 30 mins
-
Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
Lid switch broke away from top.
13 of 15 people
found this instruction helpful.
-
Brad from Wilmington, DE
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Replaceing the actual switch was easy as unscrewing two screws with the lid up. The wiring was a different story. I guess you can cut and spice and be done with it but to get to the real connection, a lot has to come apart or have very long arms to reach from the bottom. I first removed the cover to the dials by removing the side trim
... Read more
and a screw at each end near the base. That exposed the wire connection. The wire actually runs under the top therefore I had to remove the back panel partially to gain access to the wiring and holders for the wire. Just by remembering the steps while backing out, everything worked out.
Read less
Was this helpful?
Thank you for voting!
Washer vibrates excessively on spin cycle
13 of 15 people
found this instruction helpful.
-
Glenn from PROVO, UT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and di
... Read more
d that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.
17 of 27 people
found this instruction helpful.
-
Matthew from Albany, MN
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from trans ... Read more mission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from trans ... Read more mission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test
Read less
Was this helpful?
Thank you for voting!
lid would not lock, washer would not run...
12 of 13 people
found this instruction helpful.
-
John from Hale Center, Texas, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this helpful?
Thank you for voting!
The top lid switch failed so washer wouldn't run.
11 of 11 people
found this instruction helpful.
-
Katherine from Salem, VA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Removed the valance by unscrewing nuts on top back and then removing side wings. The valance can be flipped up and hung over the back of the backsheet making sure not to damage clear hose. Then remove the old switch, wire and cut off the ground wire. Moount the new switch and make sure the wire is well back from the drum by tying to the o
... Read more
ld clip that held the old wire. Connect the ground to the body now under the valance. I found a hole there and screwed the ground terminal to it with a self taping screw.This procedure allows you to replace the switch without having to take the complete washer front body off.
Read less
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Washer was leaking.. determined it was center gasket
10 of 10 people
found this instruction helpful.
-
Diane from BALTIMORE, MD
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people
found this instruction helpful.
-
Thomas from GRAIN VALLEY, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Water Level Switch Broken
11 of 14 people
found this instruction helpful.
-
Bo from Sugar Land, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair is very easy with the part found at PartSelect.com. Take the following steps to replace the water level switch:
1. Remove the front panel by unscrewing two screws on the back side
2. Pull off the dial knob from the front
3. Twist the water level switch in either way to remove the switch from the panel
4. Dis ... Read more connect the connector of control wires and water hose from the broken switch
5. Reconnect the control connector and water hose
6. Push and twist the switch to put back on the front panel
7. secure the front panel by tighten up two screws on the back side of panel
1. Remove the front panel by unscrewing two screws on the back side
2. Pull off the dial knob from the front
3. Twist the water level switch in either way to remove the switch from the panel
4. Dis ... Read more connect the connector of control wires and water hose from the broken switch
5. Reconnect the control connector and water hose
6. Push and twist the switch to put back on the front panel
7. secure the front panel by tighten up two screws on the back side of panel
Read less
Was this helpful?
Thank you for voting!
washing machine not draining
10 of 11 people
found this instruction helpful.
-
michael from princeton, TX
- Easy
- 15 - 30 mins
-
Pliers
Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.
Was this helpful?
Thank you for voting!
Replaced ring that broke and washer that was bent on the edge.
22 of 47 people
found this instruction helpful.
-
Kim from West Liberty, OH
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte
... Read more
d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
tub oscillation
12 of 17 people
found this instruction helpful.
-
leonard from phil campbell, AL
- Really Easy
- 15 - 30 mins
-
Pliers
placed washer on side and installed new pads
and returned washer upright
and returned washer upright
Was this helpful?
Thank you for voting!
Crossed threaded plastic on old valve was leaking
11 of 14 people
found this instruction helpful.
-
David from Amity, AR
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of
... Read more
the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.
Read less
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people
found this instruction helpful.
-
Peter from Boca Raton, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the
... Read more
suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Read less
Was this helpful?
Thank you for voting!