110231 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Top part of agitator was skipping/not turning
1 person
found this instruction helpful.
-
Mike from Lakewood, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator
... Read more
from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again
Read less
Was this helpful?
Thank you for voting!
agitator didn't turn
1 person
found this instruction helpful.
-
marsha from challis, ID
- Really Easy
- Less than 15 mins
-
Socket set
I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder p
... Read more
art, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!
Read less
Was this helpful?
Thank you for voting!
Agitator was not spinning.
1 person
found this instruction helpful.
-
Jeffry from Orange, CA
- Really Easy
- Less than 15 mins
-
Socket set
Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.
Was this helpful?
Thank you for voting!
Upper portion of agitator would not function!
1 person
found this instruction helpful.
-
Kenneth from Merced, CA
- Really Easy
- Less than 15 mins
-
Socket set
Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled
... Read more
the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.
Sincerely,
Ken Lancaster
Sincerely,
Ken Lancaster
Read less
Was this helpful?
Thank you for voting!
The agitator would not move.
1 person
found this instruction helpful.
-
Manuel from Tehachapi, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the center cap from the agitator, which then exposed an inner cap with rubber seal. These were both easily removed with no tools... just a slight pull. Then the center screw was exposed. I removed that "one" screw and pulled the upper agitator assembly off. The old dog ears literally fell right out. I simply ensured that I place
... Read more
d the new dog ears in the same direction as the old, which is not hard to remember because the little housing piece that holds them is molded in the angle of the ears. Putting it back in took the most time because the new ears can easily fall out. In order to overcome this I had to assemble the pieces that had been removed and carefully put them back in place. At that point I had to manage to get the screw back into position and tighten it up. I put the inner cap with seal back in place and then the agitator cap... Done! It's an old machine but works great with a simple repair. The dog ears were so inexpensive that I purchased two sets. Great site!
Read less
Was this helpful?
Thank you for voting!
Agitator quit agitating
1 person
found this instruction helpful.
-
David from Austin, TX
- Really Easy
- Less than 15 mins
-
Wrench set
Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!
Was this helpful?
Thank you for voting!
The agitator was no longer turning.
1 person
found this instruction helpful.
-
Steve from Troy, TX
- Easy
- Less than 15 mins
-
Socket set
First I popped off the very top cap of the agitator. I then used a socket extension to access the mounting bolt in the interior of the agitator. Once the bolt was loose i pulled the agitator off and dropped out the middle piece. With this out i switched the 4 cogs with the old. I then held the agitator assembly upside down and placed the
... Read more
middle piece back in. The most difficult part was aligning the agitator back onto the bottom part. Screw it back in place and pop the top back on.
Read less
Was this helpful?
Thank you for voting!
Top part of agitator not turning
1 person
found this instruction helpful.
-
Merrill from Attica, NY
- Really Easy
- Less than 15 mins
-
Socket set
The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great
Was this helpful?
Thank you for voting!
The agitator stopped working....no spinning
1 person
found this instruction helpful.
-
Christopher from Wichtia, KS
- Really Easy
- Less than 15 mins
-
Socket set
I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.
Works lik ... Read more e new!!
Works lik ... Read more e new!!
Read less
Was this helpful?
Thank you for voting!
agitator is now just annoying
1 person
found this instruction helpful.
-
Kelly from Norcross, GA
- Really Easy
- Less than 15 mins
-
Socket set
popped off the softener dispenser, pulled out seal over nut assembly, used socket wrench with extention to loosen and remove nut holding cog assembly.
slid holding ring off of the bottom (mine was black in color) pulled out old dog agitators put in new ones, reverse assembled the unit tightened it down, (be sure not to go too tight t ... Read more here is a rubber bushing under the nut) ran a small test load of laundry and it now works great!!!!
slid holding ring off of the bottom (mine was black in color) pulled out old dog agitators put in new ones, reverse assembled the unit tightened it down, (be sure not to go too tight t ... Read more here is a rubber bushing under the nut) ran a small test load of laundry and it now works great!!!!
Read less
Was this helpful?
Thank you for voting!
would not agitate
2 of 4 people
found this instruction helpful.
-
Sheila from Greensboro, NC
- Really Easy
- Less than 15 mins
-
Wrench set
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
Was this helpful?
Thank you for voting!
Agitator stopped turning with a load in it.
1 person
found this instruction helpful.
-
Harry A. from Maitland, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.
Very simple; even a cave man could do it!
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.
Very simple; even a cave man could do it!
Was this helpful?
Thank you for voting!
Top part of agitator quit agitating in one direction.
3 of 7 people
found this instruction helpful.
-
Eldon from Liberty Lake, WA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap rin ... Read more g.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap rin ... Read more g.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Read less
Was this helpful?
Thank you for voting!
Agitator wouldn't turn when washing clothes.
1 person
found this instruction helpful.
-
Kitty from Erie, PA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're i
... Read more
n). Replaced cogs in the same direction they came out. Very simple!!
Read less
Was this helpful?
Thank you for voting!
Agitator was spinning freely
1 person
found this instruction helpful.
-
Michael from Clawson, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble
repeat process to re assemble
Was this helpful?
Thank you for voting!