110231 Kenmore Washer - Instructions

All Instructions for the 110231
76 - 90 of 369

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Reolaced actuator
2 of 3 people found this instruction helpful.
  • Thomas from New Fairfield, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person found this instruction helpful.
  • Jeff from Michigan City, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re pair man.
Was this helpful?
Thank you for voting!
Top of Agitator would not rotate
1 person found this instruction helpful.
  • Depeturie from Madison, AL
  • Really Easy
  • 15 - 30 mins
  • Socket set
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person found this instruction helpful.
  • Walter from Brandon, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Was this helpful?
Thank you for voting!
agitator wasn't moving
1 person found this instruction helpful.
  • jose from lake forest, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
Was this helpful?
Thank you for voting!
Water inlet and valve froze and cracked
1 person found this instruction helpful.
  • Donna from MOUNTAINBURG, AR
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Ordered and replaced the water inlet and valve assembly from this site
Was this helpful?
Thank you for voting!
Top portion of agitator not turning
1 person found this instruction helpful.
  • James from Oldtown, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.
Was this helpful?
Thank you for voting!
Agitator doggs wore out
1 person found this instruction helpful.
  • Glenda from FUQUAY VARINA, NC
  • Really Easy
  • 15 - 30 mins
  • Socket set
Followed youtube video. Great instruction.
Was this helpful?
Thank you for voting!
No problem
1 person found this instruction helpful.
  • Luu from STANTON, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
That OK , easy.
Was this helpful?
Thank you for voting!
Agitator was not turning properly; soap left on clothes. The teeth on the agitator dogs were worn off.
1 person found this instruction helpful.
  • Carol from WEST LIBERTY, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.
Was this helpful?
Thank you for voting!
Agitation ceased
1 person found this instruction helpful.
  • Nelson from UNIONTOWN, OH
  • Very Easy
  • Less than 15 mins
  • Socket set
After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.
Was this helpful?
Thank you for voting!
agitator would not turn
1 person found this instruction helpful.
  • Sam from Surfside Beach, SC
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.
Was this helpful?
Thank you for voting!
top agitatior was slipping
1 person found this instruction helpful.
  • Steve from LANGHORNE, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Socket set
from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...
Was this helpful?
Thank you for voting!
Plastic gears wore down not allowing top half of agitator to spin
1 person found this instruction helpful.
  • Jonathon from LOCKPORT, KY
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!
Was this helpful?
Thank you for voting!
top part ofagitator not turning.
1 person found this instruction helpful.
  • Rodger from ANDOVER, OH
  • Very Easy
  • 15 - 30 mins
  • Socket set
Followed instructions on website video.
Was this helpful?
Thank you for voting!
All Instructions for the 110231
76 - 90 of 369