110231 Kenmore Washer - Instructions

All Instructions for the 110231
91 - 105 of 369

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator was skipping and seemed lose.
1 person found this instruction helpful.
  • John from WHITE BEAR LK, MN
  • Easy
  • 30 - 60 mins
  • Wrench set
Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.
Was this helpful?
Thank you for voting!
Taking the adjetator apart.
1 person found this instruction helpful.
  • David from JOELTON, TN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.
Was this helpful?
Thank you for voting!
I noticed when putting clothes in the washer and more than half full the top agitator slowed down.
1 person found this instruction helpful.
  • Janet from LINCOLNVILLE, KS
  • Very Easy
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.
Was this helpful?
Thank you for voting!
upper agitator wouldn't rotate properly/intermittently
1 person found this instruction helpful.
  • Tony from SUMNER, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed the four worn agitator directional cogs and replaced them with new ones
Was this helpful?
Thank you for voting!
Worn out Cogs
1 person found this instruction helpful.
  • Leo from Yorba Linda, CA
  • Easy
  • 15 - 30 mins
  • Socket set
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
Was this helpful?
Thank you for voting!
Top partion of agitator turned in both directions by hand and was not driven by the motor.
1 person found this instruction helpful.
  • Charles from Lindenhurst, NY
  • Easy
  • 15 - 30 mins
  • Socket set
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this helpful?
Thank you for voting!
agitator wasn't moving
1 person found this instruction helpful.
  • jose from lake forest, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
Was this helpful?
Thank you for voting!
Agitator stopped turning
1 person found this instruction helpful.
  • William from Canandaigua, NY
  • Easy
  • 15 - 30 mins
  • Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person found this instruction helpful.
  • Jeff from Michigan City, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re pair man.
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person found this instruction helpful.
  • Walter from Brandon, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Was this helpful?
Thank you for voting!
worn our Agit-dogs, agitator wouldn't pull clothes down
2 of 4 people found this instruction helpful.
  • Douglas from Wetumpka, AL
  • Really Easy
  • 15 - 30 mins
  • Socket set
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the c orrect place.
Was this helpful?
Thank you for voting!
top part ofagitator not turning.
1 person found this instruction helpful.
  • Rodger from ANDOVER, OH
  • Very Easy
  • 15 - 30 mins
  • Socket set
Followed instructions on website video.
Was this helpful?
Thank you for voting!
No problem
1 person found this instruction helpful.
  • Luu from STANTON, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
That OK , easy.
Was this helpful?
Thank you for voting!
Agitaor does not spin anymore
1 person found this instruction helpful.
  • ZHAN from MORRISVILLE, NC
  • Really Easy
  • Less than 15 mins
  • Socket set
First take the top cover off, second using socket to turn the nut loose at the center, then removing the plastic holder which has four directional cogs in it, replacing them with new one.
Was this helpful?
Thank you for voting!
washer would not agitate
1 person found this instruction helpful.
  • Marius from Buena Park, CA
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
basically pop off the top spindle cover, reach in and pull off the water cap from the agitator cog cover, unscrew the bolt holding the cog holder and pull the agittator assembly up and off the machine. Remove the piece holding the gogs in place and replace cogs making sure to put them back in the same direction as they came out. Turn the agitator upside down and stick the piece holding the cogs in and snap it in. Replace all components in reverse order they were removed, and there you are. Works great.
Was this helpful?
Thank you for voting!
All Instructions for the 110231
91 - 105 of 369