110231 Kenmore Washer - Instructions

All Instructions for the 110231
121 - 135 of 369

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator would'nt agitate
1 person found this instruction helpful.
  • Durand from Tyndall AFB, FL
  • Really Easy
  • Less than 15 mins
  • Socket set
Took off softner dispenser, took off bolt cover. Used 7/16 socket with long extension and unscrewed bolt. Pulled up on agitator and out it came. Took out directional cogs and replaced with new. Reversed procedure and I was done. Saved a lot of money by not calling a mobile repair man on this one!
Was this helpful?
Thank you for voting!
all four dog ears were broken to pieces
1 person found this instruction helpful.
  • Sherman from Kansas City, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed fabric softener dispenser. Inserted screwdriver into slot on side of cover that is on agitator and pried off. Used socket extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs . Replaced cogs in the same direction they came out. Since these instructions were here on site at the time I ordered the parts, it made the job very simple and fast...the order came very fast too.
Was this helpful?
Thank you for voting!
Washer Agitator not working properly
1 person found this instruction helpful.
  • Carleen from Las Vegas, NV
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking th e agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix
Was this helpful?
Thank you for voting!
agitator would not work
1 person found this instruction helpful.
  • Patti from Ozark, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
got the parts from parts select and got the machine repaired quickly
what a savings
repair man would have been over 100 dollars
the shipping was more than the parts but I saved greatly with no repairman
love your site and the great savings
i really loved my washing machine and hating to lose it
was so satisfi ed that I could save it after all these years
thanks
Was this helpful?
Thank you for voting!
washer not agitating
1 person found this instruction helpful.
  • Richard from Corona, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet e xtension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.
Was this helpful?
Thank you for voting!
The upper section of agitator would not agitate.
1 person found this instruction helpful.
  • Melissa from Raleigh, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Snap off softener dispenser. Pop off top of agitator with flat head screw driver. Use long handled socket ro remove agitator fastener. Lift off entire agitator assembly. Flip upside down on floor. Secure top section of agitator between feet and carefully unsnap but lifting upper portion. Look at placement of existing agitator cogs in uppe r section between feet. Remove cog retainer. Note position of cogs. Replace one cog at a time making sure they are repositioned the same way. Attach cog retainer. Place bottom portion of agitator in alignment and snap. Flip over and reinstall on washer center assembly. Place bolt and washer back into assembly and retighten. reattach cover and softener dispenser (if you have one). Done! Less than 15 minutes.
Was this helpful?
Thank you for voting!
Upper agitator would not rotate
2 of 4 people found this instruction helpful.
  • Noel from Chicago, IL
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pres sure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.
Was this helpful?
Thank you for voting!
Washer wouldn't agitate
1 person found this instruction helpful.
  • Genaro from Moreno Valley, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!
Was this helpful?
Thank you for voting!
wouldn't agitate properly
1 person found this instruction helpful.
  • Wilber from Thomaston, ME
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed the fabric softner dispenser,removed the inner cover,removed the 1/2" bolt holding the upper agitator to the lower agitator and pulled the upper agitator up and out.Remover the cog holder from inside the upper agitator and replaced the old cogs with the new.They simply set loosely in the holder.I then reversed the process of put ting the agitator back and bolting it in,inserted the small cover and dispenser.The entire job took about 5 minutes at most.
Was this helpful?
Thank you for voting!
agitator not working (again)
1 person found this instruction helpful.
  • Tanya from Garrettsville, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The dogs (directional cogs) cause the upper portion of the agitator to turn in one direction only. The clothes don't get clean unless this happens.

The material the dogs are made of wears out in a few months of use.

I buy 4 packages of them at once, every few years.

Pull off the inner cap, unscrew the bol t, remove the old cogs, put in the new ones, reverse the disassembly process and away we go.
Was this helpful?
Thank you for voting!
two halves of agitator no longer had enough friction to bind in one direction
1 person found this instruction helpful.
  • Chris from Plainville, CT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
disassembled two halves, cogs just sitting there, replaced, re-assembled
Was this helpful?
Thank you for voting!
The agitator cogs were worn out.
1 person found this instruction helpful.
  • Tammy from Wildwood, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.
Was this helpful?
Thank you for voting!
Agitator upper half didn't ratchet with the agitator motion
1 person found this instruction helpful.
  • William from Greenville, WI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
To replace the dogs that cause the ratcheting motion:

I removed the softener cup by pulling straight up. (You've probably found, as I have, that the softener cup and the bleach dispensers are problematic: the softener cup must be cleaned with every use or the old softener liquid turns to glue, and the bleach dispenser mechanism plugs and distributes bleach onto your next load, ruining entire loads of clothes.)

Then I lifted the cap covering the retaining bolt by inserting a screwdriver alongside in the square holes provided, loosening it, and lifting it out.

Then I used a socket and a very long extension to remove the retaining bolt. I lifted the agitator straight up.

The next step can be a problem: I survived it (though I did strain my back). What's required, as you can see by reading the preceding letters, is to lift sharply on the upper agitator while holding the lower agitator with your bare feet or some soft shoes. What this does, at least on my model, is to break off the tabs that are fused together over the ratcheting-dogs, which are the focus of the repair. (These tabs hold the upper and lower assemblies together, moving the dogs assembly with the lower agitator.) In my case, one of the tabs broke off a half inch below the top, but that wasn't catastrophic and I didn't lose the rest of them, so when I reassembled the two halves still snapped back together.

One problem was that when I jerked the two assemblies apart, the parts of the dogs assembly went flying. Everyone had said to make sure everything went back the same way it came apart--for me there was no way to tell what that way was, but common sense tells you which way to reinstall the new dogs; they have to catch every stroke.

To reassemble, position the dogs with the retainer cup inverted. Then hold them upside down while sliding the upper agitator down over them. This holds them in place. When sliding the upper agitator down onto the lower, make sure the slots line up and use a smooth even pressure. Snap the two halves together, bolt the agitator back into the machine, replace the cap with the large o-ring (make sure you clean and/or replace the o-ing), and reinstall the softener cup.

Et, voila! You're back in business.
Was this helpful?
Thank you for voting!
Agitator cogs were wore out
1 person found this instruction helpful.
  • Jeff from Ramsey, IL
  • Really Easy
  • Less than 15 mins
  • Socket set
I just took the bolt out of the top of the agitator which allowed me to pull the agitator straight up. Then I turned it over so the sleeve that the cogs go into could fall out. I took the old cogs out, put the new cogs in, held it upside down and lowered the agitator down onto as to not move the cogs. When it was all situated correctly I held it by the bolt as I turned it upright. Then I just lowered it back down in place inside the drum and tightened the bolt back down. Done.
The washer works just like new.
Was this helpful?
Thank you for voting!
agitator cogs wore out
1 person found this instruction helpful.
  • Wendell from Hudson, NY
  • Really Easy
  • Less than 15 mins
  • Socket set
Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."
Was this helpful?
Thank you for voting!
All Instructions for the 110231
121 - 135 of 369