110221 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
agitator wasn't moving
1 person
found this instruction helpful.
-
jose from lake forest, CA
- Really Easy
- 15 - 30 mins
-
Socket set
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back
... Read more
on the instructions.
Read less
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person
found this instruction helpful.
-
Jeff from Michigan City, IN
- Really Easy
- 15 - 30 mins
-
Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re
... Read more
pair man.
Read less
Was this helpful?
Thank you for voting!
Agitator stopped turning
1 person
found this instruction helpful.
-
William from Canandaigua, NY
- Easy
- 15 - 30 mins
-
Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
Agitator would not agitate properly
1 person
found this instruction helpful.
-
Dawn from Little Rock, AR
- Easy
- 15 - 30 mins
-
Socket set
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the a
... Read more
gitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Read less
Was this helpful?
Thank you for voting!
Top partion of agitator turned in both directions by hand and was not driven by the motor.
1 person
found this instruction helpful.
-
Charles from Lindenhurst, NY
- Easy
- 15 - 30 mins
-
Socket set
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this helpful?
Thank you for voting!
Top of Agitator would not rotate
1 person
found this instruction helpful.
-
Depeturie from Madison, AL
- Really Easy
- 15 - 30 mins
-
Socket set
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Read less
Was this helpful?
Thank you for voting!
upper agitator not spinning
1 person
found this instruction helpful.
-
roger from Delanco, NJ
- Easy
- 15 - 30 mins
-
Socket set
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself fro
... Read more
m this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Top of agitator was not working
1 person
found this instruction helpful.
-
David from Warren, MI
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Socket set
I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
agitator stopped working
1 person
found this instruction helpful.
-
KENNETH from HAUGHTON, LA
- Really Easy
- 15 - 30 mins
-
Socket set
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this helpful?
Thank you for voting!
Top portion of agitator not turning
1 person
found this instruction helpful.
-
James from Oldtown, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I
... Read more
also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.
Read less
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Linda from Arnold, MD
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
Read less
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person
found this instruction helpful.
-
ROBERT from OXLY, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
top part ofagitator not turning.
1 person
found this instruction helpful.
-
Rodger from ANDOVER, OH
- Very Easy
- 15 - 30 mins
-
Socket set
Followed instructions on website video.
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person
found this instruction helpful.
-
David from KISSIMMEE, FL
- Really Easy
- 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest
... Read more
part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Read less
Was this helpful?
Thank you for voting!
Agitator doggs wore out
1 person
found this instruction helpful.
-
Glenda from FUQUAY VARINA, NC
- Really Easy
- 15 - 30 mins
-
Socket set
Followed youtube video. Great instruction.
Was this helpful?
Thank you for voting!