110221 Kenmore Washer - Instructions

All Instructions for the 110221
76 - 90 of 415

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
agitator was making a large amount of noise
2 of 2 people found this instruction helpful.
  • Timothy from Kansas City, MD
  • Easy
  • 15 - 30 mins
  • Socket set
After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!
Was this helpful?
Thank you for voting!
Would not Agitate
2 of 2 people found this instruction helpful.
  • Scott from HILBERT, WI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Tip the washer on its back remove the agitator install new one under 15 minutes
Was this helpful?
Thank you for voting!
Washer would not drain
2 of 2 people found this instruction helpful.
  • Kris from W MANSFIELD, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Im a 58 year old single woman. Swap out of pump motor was so easy. Took less than 15 min. Ordered the part on Tuesday it came the next day. I installed it and did 4 loads of laundry.
Great company.
Was this helpful?
Thank you for voting!
Washer not agitating
2 of 2 people found this instruction helpful.
  • Dianne from WALES, MI
  • Very Easy
  • Less than 15 mins
  • Socket set
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
Was this helpful?
Thank you for voting!
Replaced the dog ears.
2 of 2 people found this instruction helpful.
  • Todd from Milwaukee, WI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this helpful?
Thank you for voting!
Top half of agitator would not agitate.
2 of 2 people found this instruction helpful.
  • Chris from Kernersville, NC
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts i n 72 hours. $10.00 bucks and never left the house.
Was this helpful?
Thank you for voting!
Found seal had split on agitator cap
3 of 5 people found this instruction helpful.
  • Kim from Cleveland, OH
  • Really Easy
  • Less than 15 mins
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people found this instruction helpful.
  • Joe from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Was this helpful?
Thank you for voting!
Easy to install
2 of 2 people found this instruction helpful.
  • John from LEXINGTON, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I just drained the washer and unscrewed the 3 screws unhooked the hose clamp and installed the new one attached the hose and hose clip. Really easy. Took longer to try up water in floor than installing.
Was this helpful?
Thank you for voting!
Agitator cogs all broken
2 of 2 people found this instruction helpful.
  • Kelly from AMARILLO, TX
  • Very Easy
  • Less than 15 mins
  • Socket set
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put b ack in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
Was this helpful?
Thank you for voting!
Agitator not moving
2 of 2 people found this instruction helpful.
  • Kevin from ALBUQUERQUE, NM
  • Very Easy
  • Less than 15 mins
  • Socket set
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Timing tabs securing the agitator center
2 of 2 people found this instruction helpful.
  • Keith from Mount Vernon, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round cente r cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this helpful?
Thank you for voting!
All Instructions for the 110221
76 - 90 of 415