110221 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud banging during spinning
3 of 5 people
found this instruction helpful.
-
Tom from LONG BEACH, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp
... Read more
ool washers!
Read less
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people
found this instruction helpful.
-
John from TEXAS CITY, TX
- Really Easy
- 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the
... Read more
final rod in the round holder. I asked my wife for assistance.
Read less
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people
found this instruction helpful.
-
Tracy from CONWAY, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
Water leak into washer drum
2 of 3 people
found this instruction helpful.
-
Richard E from BURKE, VA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people
found this instruction helpful.
-
Shane from CLINTON TWP, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu
... Read more
ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Read less
Was this helpful?
Thank you for voting!
Agitator would not agitate
2 of 3 people
found this instruction helpful.
-
Daniel from Beaufort, SC
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people
found this instruction helpful.
-
Joseph from Kalkaska, MI
- Really Easy
- Less than 15 mins
-
Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Top Agitator would turn
2 of 3 people
found this instruction helpful.
-
EDWARD from CATONSVILLE, MD
- Easy
- Less than 15 mins
-
Socket set
First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Co
... Read more
gs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .
Read less
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people
found this instruction helpful.
-
joseph from san antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and
... Read more
prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Read less
Was this helpful?
Thank you for voting!
Reolaced actuator
2 of 3 people
found this instruction helpful.
-
Thomas from New Fairfield, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
Was this helpful?
Thank you for voting!
Top part of agitator not working
2 of 3 people
found this instruction helpful.
-
Roger from St. Albans, WV
- Easy
- Less than 15 mins
-
Nutdriver
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the
... Read more
shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Read less
Was this helpful?
Thank you for voting!
Top agitator would not agitate
2 of 3 people
found this instruction helpful.
-
Michael from Clarksville, TN
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy
Was this helpful?
Thank you for voting!
Replaced cogs in agitator
2 of 3 people
found this instruction helpful.
-
Allen from Simpsonville, KY
- Really Easy
- Less than 15 mins
Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand.
... Read more
Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.
Read less
Was this helpful?
Thank you for voting!
Water inlet and valve froze and cracked
1 person
found this instruction helpful.
-
Donna from MOUNTAINBURG, AR
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Ordered and replaced the water inlet and valve assembly from this site
Was this helpful?
Thank you for voting!
Worn out Cogs
1 person
found this instruction helpful.
-
Leo from Yorba Linda, CA
- Easy
- 15 - 30 mins
-
Socket set
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
the rest was very straight forward.
Was this helpful?
Thank you for voting!