110221 Kenmore Washer - Instructions

All Instructions for the 110221
121 - 135 of 415

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No problem
1 person found this instruction helpful.
  • Luu from STANTON, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
That OK , easy.
Was this helpful?
Thank you for voting!
Agitator was not turning properly; soap left on clothes. The teeth on the agitator dogs were worn off.
1 person found this instruction helpful.
  • Carol from WEST LIBERTY, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.
Was this helpful?
Thank you for voting!
Agitator was free wheeling
1 person found this instruction helpful.
  • Dennis from Spring Grove, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person found this instruction helpful.
  • Walter from Brandon, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Was this helpful?
Thank you for voting!
worn our Agit-dogs, agitator wouldn't pull clothes down
2 of 4 people found this instruction helpful.
  • Douglas from Wetumpka, AL
  • Really Easy
  • 15 - 30 mins
  • Socket set
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the c orrect place.
Was this helpful?
Thank you for voting!
Agitator was spinning freely
1 person found this instruction helpful.
  • Michael from Clawson, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble
Was this helpful?
Thank you for voting!
Agitator wouldn't turn when washing clothes.
1 person found this instruction helpful.
  • Kitty from Erie, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're i n). Replaced cogs in the same direction they came out. Very simple!!
Was this helpful?
Thank you for voting!
Top part of agitator quit agitating in one direction.
3 of 7 people found this instruction helpful.
  • Eldon from Liberty Lake, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap rin g.
Replace the (4) drive dogs, and reassemble in reverse order.

As far as repairs go, this one is really easy.
Was this helpful?
Thank you for voting!
would not agitate
2 of 4 people found this instruction helpful.
  • Sheila from Greensboro, NC
  • Really Easy
  • Less than 15 mins
  • Wrench set
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
Was this helpful?
Thank you for voting!
Agitator stopped turning with a load in it.
1 person found this instruction helpful.
  • Harry A. from Maitland, FL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!
Was this helpful?
Thank you for voting!
Agitaor does not spin anymore
1 person found this instruction helpful.
  • ZHAN from MORRISVILLE, NC
  • Really Easy
  • Less than 15 mins
  • Socket set
First take the top cover off, second using socket to turn the nut loose at the center, then removing the plastic holder which has four directional cogs in it, replacing them with new one.
Was this helpful?
Thank you for voting!
washer would not agitate
1 person found this instruction helpful.
  • Marius from Buena Park, CA
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
basically pop off the top spindle cover, reach in and pull off the water cap from the agitator cog cover, unscrew the bolt holding the cog holder and pull the agittator assembly up and off the machine. Remove the piece holding the gogs in place and replace cogs making sure to put them back in the same direction as they came out. Turn the agitator upside down and stick the piece holding the cogs in and snap it in. Replace all components in reverse order they were removed, and there you are. Works great.
Was this helpful?
Thank you for voting!
Top part of agitator was skipping/not turning
1 person found this instruction helpful.
  • Mike from Lakewood, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again
Was this helpful?
Thank you for voting!
agitator didn't turn
1 person found this instruction helpful.
  • marsha from challis, ID
  • Really Easy
  • Less than 15 mins
  • Socket set
I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder p art, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!
Was this helpful?
Thank you for voting!
Agitator was not spinning.
1 person found this instruction helpful.
  • Jeffry from Orange, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.
Was this helpful?
Thank you for voting!
All Instructions for the 110221
121 - 135 of 415