110214 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
The lid lock switch on our clothes washer went out
-
Steven from Keenesburg, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this helpful?
Thank you for voting!
would not unlock
-
Michael from Lincoln, RI
- Easy
- 15 - 30 mins
-
Screw drivers
Disassembled ,as assembled.
Was this helpful?
Thank you for voting!
Bad latch lock
-
David B from Madison, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Latch Assembly and lock broke
-
DIANE*RACHAL from SHREVEPORT, LA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
I taught I might have to replace the whole machine. Then I realize we had power but the latch and lock assembly wasn't locking for the machine to lock and start to wash. Unplug the washer, took the top off of washer, unscrew two bolts from latch assembly, replace latch assembly and two bolts. then unscrew two bolts from lock and replace
... Read more
it. Machine works great now.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
valve frose in cold temps 8 degrees out
-
susan from simpsonville, SC
- Really Easy
- Less than 15 mins
-
Nutdriver
lift top with putty knife unhook wire , take two screws out and replace with new part.
Was this helpful?
Thank you for voting!
Lid lock would not ingague.
-
Tom from Franklin, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Was this helpful?
Thank you for voting!
Missing lid hinge bearing
-
Kim from Oviedo, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an
... Read more
d into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Read less
Was this helpful?
Thank you for voting!