110214 Kenmore Washer - Instructions

All Instructions for the 110214
31 - 45 of 53

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No agitation
3 of 3 people found this instruction helpful.
  • Jim from ACUSHNET, MA
  • Very Easy
  • 15 - 30 mins
Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.
Was this helpful?
Thank you for voting!
water inlet valve stopped working
3 of 3 people found this instruction helpful.
  • Zoran from ROCKVILLE, MD
  • Really Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.
Was this helpful?
Thank you for voting!
Wash plate spinning. Clothes not spun out.
3 of 4 people found this instruction helpful.
  • Gregory from GREENFILD TWP, PA
  • A Bit Difficult
  • 1- 2 hours
  • Socket set
Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 c heaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people found this instruction helpful.
  • Joe from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
violent basket wobble
3 of 5 people found this instruction helpful.
  • Keith from DUNBARTON, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove basket and replace drive hub kit
Was this helpful?
Thank you for voting!
Water leak into washer drum
2 of 3 people found this instruction helpful.
  • Richard E from BURKE, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people found this instruction helpful.
  • Joseph from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Water inlet and valve froze and cracked
1 person found this instruction helpful.
  • Donna from MOUNTAINBURG, AR
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Ordered and replaced the water inlet and valve assembly from this site
Was this helpful?
Thank you for voting!
Washer would not agitate or spin and took over 2 hours to go through all cycles.
1 person found this instruction helpful.
  • Danny from HARRISBURG, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The p lug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people found this instruction helpful.
  • Enrique from Miami Shores, FL
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w asher door bang shut.Took longer than expected, but each procedure was simple.
Was this helpful?
Thank you for voting!
Washer would go into the cycle to rinse dry.
1 of 2 people found this instruction helpful.
  • Daniel from WARMINSTER, PA
  • Really Easy
  • 30 - 60 mins
  • Socket set
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this helpful?
Thank you for voting!
no spin
1 of 3 people found this instruction helpful.
  • Earl from BARRYTON, MI
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
reviewed video of repair and repaired now washer works as it should . thank you
Was this helpful?
Thank you for voting!
door latch broke
0 of 1 people found this instruction helpful.
  • Diana from Chimacum, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people found this instruction helpful.
  • Brian from DREXEL HILL, PA
  • Easy
  • 30 - 60 mins
  • Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!
All Instructions for the 110214
31 - 45 of 53