110214 Kenmore Washer - Instructions

All Instructions for the 110214
16 - 30 of 53

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
replaced drain hose that was missing
12 of 20 people found this instruction helpful.
  • Delmar from EAST TROY, WI
  • Really Easy
  • 30 - 60 mins
  • Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
drive hub splines were warn off. Thus no agitation was possible. Coins from laundry probably made increased friction to cause excessive ware on the splines.
8 of 8 people found this instruction helpful.
  • Wayne from HILTON, NY
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Was this helpful?
Thank you for voting!
Slow Spin Cycle with Fast/Normal Agitator
8 of 8 people found this instruction helpful.
  • Michael from AURORA, CO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Socket set
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!
Was this helpful?
Thank you for voting!
During the Spin cycle the washer was noisy and moved around
8 of 9 people found this instruction helpful.
  • JOHN from HERNANDO, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
Was this helpful?
Thank you for voting!
After removing the bolt on top of the agitator, it agitator was very difficult to get out.
7 of 7 people found this instruction helpful.
  • John from SALEM, VA
  • Very Difficult
  • More than 2 hours
  • Screw drivers, Socket set
I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in a round the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people found this instruction helpful.
  • Terry from HANCOCK, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
Washer gets stuck on Rinse and not complete the cycle.
6 of 6 people found this instruction helpful.
  • Charles from SEALY, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.
Was this helpful?
Thank you for voting!
Lid lock/latch stuck closed
6 of 7 people found this instruction helpful.
  • David from BELMONT, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
Very wet clothes after load was complete
5 of 6 people found this instruction helpful.
  • Craig from CRARY, ND
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline groo ves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt
Was this helpful?
Thank you for voting!
the splines were worn out on the hub assembley
5 of 6 people found this instruction helpful.
  • Johnny from NORTH JUDSON, IN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .
Was this helpful?
Thank you for voting!
Water would not stop running over filled the washer
4 of 4 people found this instruction helpful.
  • Mary from GROVER HILL, OH
  • Very Easy
  • 30 - 60 mins
  • Socket set
Unplugged the washer turned off the water disconnected the water lines then took the cover off and disconnected the wires and took 2 screws out and took the old part out and put the new 1 in
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people found this instruction helpful.
  • James from INDIAN LAKE, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
water inlet valve stopped working
3 of 3 people found this instruction helpful.
  • Zoran from ROCKVILLE, MD
  • Really Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.
Was this helpful?
Thank you for voting!
Stripped screws on a hub drive replacement
3 of 3 people found this instruction helpful.
  • Bruce from GLOBE, AZ
  • Easy
  • 15 - 30 mins
  • Screw drivers
Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.
Was this helpful?
Thank you for voting!
cold water inlet valve bad
3 of 3 people found this instruction helpful.
  • Doris from CONCORD, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers
Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.
Was this helpful?
Thank you for voting!
All Instructions for the 110214
16 - 30 of 53