110213 Kenmore Washer - Instructions

All Instructions for the 110213
91 - 105 of 446

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Top agitator did not work
3 of 3 people found this instruction helpful.
  • George from Danbury, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the a gitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people found this instruction helpful.
  • JOSE from MILLBURY, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
Top section of agitator was slipping.
3 of 4 people found this instruction helpful.
  • Stephen from Hot Springs, AR
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.
Was this helpful?
Thank you for voting!
Wash plate spinning. Clothes not spun out.
3 of 4 people found this instruction helpful.
  • Gregory from GREENFILD TWP, PA
  • A Bit Difficult
  • 1- 2 hours
  • Socket set
Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 c heaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
Timing tabs securing the agitator center
2 of 2 people found this instruction helpful.
  • Keith from Mount Vernon, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round cente r cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Remove and replace drain pump
2 of 2 people found this instruction helpful.
  • Katherine from Saint Cloud, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people found this instruction helpful.
  • Tracy from CONWAY, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
would not spin
2 of 2 people found this instruction helpful.
  • John from INDIANAPOLIS, IN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this helpful?
Thank you for voting!
On Spin cycle washer jumping all over the place.
2 of 2 people found this instruction helpful.
  • Tuan from LADSON, SC
  • Really Easy
  • 15 - 30 mins
  • Socket set
Just follow the video! Very easy.
Was this helpful?
Thank you for voting!
out of balance
2 of 2 people found this instruction helpful.
  • Charles from ARVADA, CO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
The info. was really helpful
Was this helpful?
Thank you for voting!
All Instructions for the 110213
91 - 105 of 446