110213 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water would drip into tub between uses
5 of 5 people
found this instruction helpful.
-
Dale from MANDAN, ND
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged washer, turn off water to washer, removed water lines from washer, pull washer away from wall, removed about 5 screws from top access panel and remove, used putty knife to release clips from both sides of front control panel and lay forward, removed three screws from valve, disconnect hose from valve. Reassemble in reverse order
... Read more
. Not a bad idea to run a little water into bucket from both supply line to remove any foreign material that may have let lose from shut off valve before reconnecting to washer.
Read less
Was this helpful?
Thank you for voting!
heavy loads did not spin dry properly
6 of 8 people
found this instruction helpful.
-
Chet from CLEARWATER, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Other Parts Used:
Was this helpful?
Thank you for voting!
Grinding noise from the gearcase.
5 of 5 people
found this instruction helpful.
-
D from DISTRICT HTS, MD
- Very Easy
- 1- 2 hours
-
Screw drivers, Socket set
Actually, I "Youtubed" it. I entered the info from the washer and found what was similar. What would help is when you tilt the washer (on back or front) so you can look at what you're going to work on to match (or closely match) what is on Youtube. It is SO easy, it's unbelievable.
Was this helpful?
Thank you for voting!
Washer was out of balance on spin cycle
5 of 5 people
found this instruction helpful.
-
Charles from Grizzly Flats, CA
- Easy
- 1- 2 hours
-
Pliers
I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loose pulley
7 of 11 people
found this instruction helpful.
-
Joseph from BAKER, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Tightened up the pulley as the video showed me that might be the issue.
Other Parts Used:
Was this helpful?
Thank you for voting!
the splines were worn out on the hub assembley
5 of 6 people
found this instruction helpful.
-
Johnny from NORTH JUDSON, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .
Was this helpful?
Thank you for voting!
The washer stopped draining.All the pump motor did was hum.
5 of 6 people
found this instruction helpful.
-
Michael from Staten Island, NY
- Easy
- 1- 2 hours
-
Pliers, Socket set
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machin
... Read more
e worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Read less
Was this helpful?
Thank you for voting!
Very wet clothes after load was complete
5 of 6 people
found this instruction helpful.
-
Craig from CRARY, ND
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline groo
... Read more
ves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt
Read less
Was this helpful?
Thank you for voting!
Water would not stop running over filled the washer
4 of 4 people
found this instruction helpful.
-
Mary from GROVER HILL, OH
- Very Easy
- 30 - 60 mins
-
Socket set
Unplugged the washer turned off the water disconnected the water lines then took the cover off and disconnected the wires and took 2 screws out and took the old part out and put the new 1 in
Was this helpful?
Thank you for voting!
tub motor shot
5 of 7 people
found this instruction helpful.
-
melanie from GREENFIELD, IN
- Really Easy
- 30 - 60 mins
Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!!
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times wi ... Read more th NO answer, only automated.
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times wi ... Read more th NO answer, only automated.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The washer was vibrating very bad on large loads
4 of 4 people
found this instruction helpful.
-
Mark from SAINT CLOUD, FL
- Very Easy
- 30 - 60 mins
-
Screw drivers
Using the parts I ordered and following the instructions provided in the video from partselect.com made the repair very easy and solved the problem
Other Parts Used:
Was this helpful?
Thank you for voting!
The capacitor exploded, broke the plastic cover that held it to the body of the machine and blow itself clear of the wires
4 of 4 people
found this instruction helpful.
-
Jay from AMELIA CT HSE, VA
- Very Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I removed the back access panel and what was left of the capacitor mounting device (the capacitor (or what was left of it) was laying against the access panel). I mounted the new capacitor which had a metal strap for mounting. I removed the small, black, wire mounting device that was still plugged in to the old capacitor and slipped the
... Read more
wires through that device. After reviewing how to reattach the wires (it turned out the polarity on my capacitor did not matter) I plugged the wires in using the wire mounting device. Once I closed it back up everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people
found this instruction helpful.
-
James from INDIAN LAKE, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people
found this instruction helpful.
-
Lucas from ARKANSAS CITY, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
The washer would walk across the floor
4 of 5 people
found this instruction helpful.
-
William from BROOKFIELD, WI
- Very Easy
- 30 - 60 mins
-
Socket set
Watched the video. It was by far the easiest repair I've ever done. The washer is happy and stays in it place
Other Parts Used:
Was this helpful?
Thank you for voting!