110213 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water inlet nozzle was stripped and leak
24 of 50 people
found this instruction helpful.
-
Armand from WESTPORT, MA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
The tub would spin but it was weak. The splines were stripped on the drive hub.
11 of 12 people
found this instruction helpful.
-
Doug from EAU CLAIRE, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Pulled the agitator, un-screwed the drive hub, cleaned the splines on the transmission, vacuumed the debris out of the tub. The repair video said to put towels or something down in the tub so if you drop a screw it will catch it. Put it back together and re-calibrated it. It didn't want to go into the calibrate mode until i moved the mode
... Read more
switch all the way to the left and then right first. Good quality factory parts!
Read less
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people
found this instruction helpful.
-
Thomas from GRAIN VALLEY, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Washer wouldn't start - Flashing Lid Light
13 of 20 people
found this instruction helpful.
-
Marc from HOPE MILLS, NC
- Easy
- 30 - 60 mins
-
Screw drivers
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Read less
Was this helpful?
Thank you for voting!
Hot water valve would barely open - take 35 mins to fill washer
10 of 11 people
found this instruction helpful.
-
Kevin from ARLINGTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< ... Read more br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< ... Read more br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Read less
Was this helpful?
Thank you for voting!
Wouldn’t drain pump made loud noise
10 of 13 people
found this instruction helpful.
-
REED from BUCHANAN, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people
found this instruction helpful.
-
Elzoria from FROSTPROOF, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people
found this instruction helpful.
-
Delmar from EAST TROY, WI
- Really Easy
- 30 - 60 mins
-
Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
Slow Spin Cycle with Fast/Normal Agitator
8 of 8 people
found this instruction helpful.
-
Michael from AURORA, CO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Socket set
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound
... Read more
of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!
Read less
Was this helpful?
Thank you for voting!
drive hub splines were warn off. Thus no agitation was possible. Coins from laundry probably made increased friction to cause excessive ware on the splines.
8 of 8 people
found this instruction helpful.
-
Wayne from HILTON, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the
... Read more
force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Read less
Was this helpful?
Thank you for voting!
During the Spin cycle the washer was noisy and moved around
8 of 9 people
found this instruction helpful.
-
JOHN from HERNANDO, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no
... Read more
tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
Read less
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people
found this instruction helpful.
-
Barbara from RICHMOND, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!
washer is unbalanced during a spin cycle
7 of 7 people
found this instruction helpful.
-
Tiffany from NORTH OLMSTED, OH
- Really Easy
- Less than 15 mins
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this helpful?
Thank you for voting!