110213 Kenmore Washer - Instructions

All Instructions for the 110213
46 - 60 of 446

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
I followed the video guide, which was excellent
7 of 7 people found this instruction helpful.
  • Richard from NAPLES, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.
Was this helpful?
Thank you for voting!
After removing the bolt on top of the agitator, it agitator was very difficult to get out.
7 of 7 people found this instruction helpful.
  • John from SALEM, VA
  • Very Difficult
  • More than 2 hours
  • Screw drivers, Socket set
I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in a round the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
Was this helpful?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
8 of 10 people found this instruction helpful.
  • Terry from HANCOCK, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people found this instruction helpful.
  • Terry from HANCOCK, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
When washer would go into spin cycle it would shake violently. This also prevented the spin cycle from completing leaving clothes soaked
7 of 8 people found this instruction helpful.
  • Jonathan from NEW BRAUNFELS, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed videos sent with the repair items. It was very easy and solved my issue. My washer did not have the centering springs to begin with so I was unsure if I even needed them. But after replacing all the suspension rods and adding the pack of centering springs this has solved my issues
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people found this instruction helpful.
  • Ernestine from CARRIERE, MS
  • Really Easy
  • 30 - 60 mins
  • Socket set
Remove top of washer suspension
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people found this instruction helpful.
  • Larry from Edgewood, TX
  • Really Easy
  • Less than 15 mins
  • Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
The wash cycle made a loud grinding noise when it went from filling to wash.
6 of 6 people found this instruction helpful.
  • Angelo from PORTLAND, ME
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Was this helpful?
Thank you for voting!
Suspension rods were worn; washer is 10+ years old
7 of 9 people found this instruction helpful.
  • William from NAPERVILLE, IL
  • Easy
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Replaced the suspension rods, suspension rod supports, main drive belt, tub centering springs, water supply hoes, and washer drain hose. Taped new front suspension rods to side of tub to ensure that they did not slide down when raising the washer off its back from the floor. Had a helper lift the tub, which made attaching the new suspensi on rods easy. The tub is extremely heavy so by a helper lifting it up it made attaching the new suspension rods much easier. IMPORTANT: According to the technician's manual, which was taped to the inside of the washer, it is absolutely necessary to recalibrate the washer after replacing any suspension parts. We did this by following the instructions in the tech manual. Failure to recalibrate a washer could result in poor performance. The procedure is different for each brand or model of washer, but again is absolutely essential after replacing suspension parts of any kind. For some unknown reason, our washer did not have the tub centering springs. Our model should have had the springs.Facing the washer, we attached one to the front left tub housing and one to right rear of the tub housing. Recommend that anyone watch the installation videos for the suspension rods, center springs, and main drive belt before attempting the repairs.
Was this helpful?
Thank you for voting!
Washer gets stuck on Rinse and not complete the cycle.
6 of 6 people found this instruction helpful.
  • Charles from SEALY, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.
Was this helpful?
Thank you for voting!
Lid lock/latch stuck closed
6 of 7 people found this instruction helpful.
  • David from BELMONT, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
Gear stripped on main spline
6 of 7 people found this instruction helpful.
  • Bernard from ARIZONA CITY, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this helpful?
Thank you for voting!
Rock and roll on spin
6 of 7 people found this instruction helpful.
  • Bruce from LANDENBERG, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver
Replaced the suspension rods.
Must be done on its side as the rods only pull down. There is no slot.
Was this helpful?
Thank you for voting!
Top section of agitator would not spin.
6 of 7 people found this instruction helpful.
  • Russell from Hyannis, MA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]
Was this helpful?
Thank you for voting!
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people found this instruction helpful.
  • TERRY from WAUKEE, IA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this helpful?
Thank you for voting!
All Instructions for the 110213
46 - 60 of 446