110213 Kenmore Washer - Instructions

All Instructions for the 110213
106 - 120 of 446

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water drained but would not spin.
2 of 2 people found this instruction helpful.
  • Ramona from MESA, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.
Was this helpful?
Thank you for voting!
agitator was making a large amount of noise
2 of 2 people found this instruction helpful.
  • Timothy from Kansas City, MD
  • Easy
  • 15 - 30 mins
  • Socket set
After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!
Was this helpful?
Thank you for voting!
The top agitator was not spinning
2 of 2 people found this instruction helpful.
  • Alec from Indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3 /8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.
Was this helpful?
Thank you for voting!
Top half of agitator would not agitate.
2 of 2 people found this instruction helpful.
  • Chris from Kernersville, NC
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts i n 72 hours. $10.00 bucks and never left the house.
Was this helpful?
Thank you for voting!
violent basket wobble
3 of 5 people found this instruction helpful.
  • Keith from DUNBARTON, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove basket and replace drive hub kit
Was this helpful?
Thank you for voting!
Spin cycle was way out of wack, like it was over loaded to 1 side
2 of 2 people found this instruction helpful.
  • David from VACAVILLE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, whic h you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Was this helpful?
Thank you for voting!
Washer wasn’t spinning fast enough to get the water out and it had a slight burning electrical smell.
2 of 2 people found this instruction helpful.
  • craig from Oxford, CT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
I simply followed your clutch drive repair video on YouTube, that wasn’t the problem so I replaced the motor… remove the cover that goes over the drive belt by taking out the two screws, remove the belt, unplug the wire connector going to the motor and remove the two bolts that hold it up and it falls right into your hand. Then reverse the process and that’s it. Very easy repair.
Was this helpful?
Thank you for voting!
Agitator cogs all broken
2 of 2 people found this instruction helpful.
  • Kelly from AMARILLO, TX
  • Very Easy
  • Less than 15 mins
  • Socket set
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put b ack in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
Was this helpful?
Thank you for voting!
Agitator not moving
2 of 2 people found this instruction helpful.
  • Kevin from ALBUQUERQUE, NM
  • Very Easy
  • Less than 15 mins
  • Socket set
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
Was this helpful?
Thank you for voting!
Washer not agitating
2 of 2 people found this instruction helpful.
  • Dianne from WALES, MI
  • Very Easy
  • Less than 15 mins
  • Socket set
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
Was this helpful?
Thank you for voting!
Replaced the dog ears.
2 of 2 people found this instruction helpful.
  • Todd from Milwaukee, WI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this helpful?
Thank you for voting!
Found seal had split on agitator cap
3 of 5 people found this instruction helpful.
  • Kim from Cleveland, OH
  • Really Easy
  • Less than 15 mins
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people found this instruction helpful.
  • Joe from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Was this helpful?
Thank you for voting!
Top agitator would not agitate
2 of 3 people found this instruction helpful.
  • Michael from Clarksville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy
Was this helpful?
Thank you for voting!
Replaced cogs in agitator
2 of 3 people found this instruction helpful.
  • Allen from Simpsonville, KY
  • Really Easy
  • Less than 15 mins
Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.
Was this helpful?
Thank you for voting!
All Instructions for the 110213
106 - 120 of 446