110213 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator would not agitate
2 of 3 people
found this instruction helpful.
-
Daniel from Beaufort, SC
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people
found this instruction helpful.
-
Joseph from Kalkaska, MI
- Really Easy
- Less than 15 mins
-
Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Top Agitator would turn
2 of 3 people
found this instruction helpful.
-
EDWARD from CATONSVILLE, MD
- Easy
- Less than 15 mins
-
Socket set
First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Co
... Read more
gs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .
Read less
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people
found this instruction helpful.
-
joseph from san antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and
... Read more
prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Read less
Was this helpful?
Thank you for voting!
Top part of agitator not working
2 of 3 people
found this instruction helpful.
-
Roger from St. Albans, WV
- Easy
- Less than 15 mins
-
Nutdriver
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the
... Read more
shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Read less
Was this helpful?
Thank you for voting!
washer shake hole machine from begin spin about 11/2 ' h
3 of 6 people
found this instruction helpful.
-
Dieu from Houston, TX
- A Bit Difficult
- 30 - 60 mins
chage out part and washer still shake
Was this helpful?
Thank you for voting!
when in spin mode machine walks around the cellar
2 of 3 people
found this instruction helpful.
-
john from Carteret, NJ
- Difficult
- 30 - 60 mins
-
Nutdriver
Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem
Was this helpful?
Thank you for voting!
Water leak into washer drum
2 of 3 people
found this instruction helpful.
-
Richard E from BURKE, VA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people
found this instruction helpful.
-
Shane from CLINTON TWP, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu
... Read more
ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Read less
Was this helpful?
Thank you for voting!
upper part of agitator did not turn because of worn out teeth on the agitator cogs.
1 person
found this instruction helpful.
-
Zina from Hot Springs Villlage, AR
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Mos
... Read more
t of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina
Read less
Was this helpful?
Thank you for voting!
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
1 person
found this instruction helpful.
-
Douglas from BEECH ISLAND, SC
- Easy
- 30 - 60 mins
-
Nutdriver
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this helpful?
Thank you for voting!
Door alignment
2 of 4 people
found this instruction helpful.
-
Amy from INMAN, SC
- Really Easy
- 30 - 60 mins
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this helpful?
Thank you for voting!
Washer shaking and banging loudly during spin cycle
1 person
found this instruction helpful.
-
Dan from KISSIMMEE, FL
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Replaced the suspension rods
Was this helpful?
Thank you for voting!
Extreme imbalance
1 person
found this instruction helpful.
-
Jerry from OROVILLE, WA
- Really Easy
- 30 - 60 mins
-
Pliers
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in l
... Read more
ess than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Read less
Was this helpful?
Thank you for voting!
Agitator wouldn't agitate
1 person
found this instruction helpful.
-
Timothy from PRAGUE, OK
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..
... Read more
reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..
Read less
Was this helpful?
Thank you for voting!