110212 Kenmore Washer - Instructions

All Instructions for the 110212
106 - 120 of 423

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Rinse cycle kept repeating, did not spin clothes
2 of 3 people found this instruction helpful.
  • Shane from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this helpful?
Thank you for voting!
Water leak into washer drum
2 of 3 people found this instruction helpful.
  • Richard E from BURKE, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this helpful?
Thank you for voting!
Top part of agitator not working
2 of 3 people found this instruction helpful.
  • Roger from St. Albans, WV
  • Easy
  • Less than 15 mins
  • Nutdriver
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Was this helpful?
Thank you for voting!
Top Agitator would turn
2 of 3 people found this instruction helpful.
  • EDWARD from CATONSVILLE, MD
  • Easy
  • Less than 15 mins
  • Socket set
First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Co gs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .
Was this helpful?
Thank you for voting!
The upper section of agitator would not agitate.
1 person found this instruction helpful.
  • Melissa from Raleigh, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Snap off softener dispenser. Pop off top of agitator with flat head screw driver. Use long handled socket ro remove agitator fastener. Lift off entire agitator assembly. Flip upside down on floor. Secure top section of agitator between feet and carefully unsnap but lifting upper portion. Look at placement of existing agitator cogs in uppe r section between feet. Remove cog retainer. Note position of cogs. Replace one cog at a time making sure they are repositioned the same way. Attach cog retainer. Place bottom portion of agitator in alignment and snap. Flip over and reinstall on washer center assembly. Place bolt and washer back into assembly and retighten. reattach cover and softener dispenser (if you have one). Done! Less than 15 minutes.
Was this helpful?
Thank you for voting!
Upper agitator would not rotate
2 of 4 people found this instruction helpful.
  • Noel from Chicago, IL
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pres sure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.
Was this helpful?
Thank you for voting!
agitator would not work
1 person found this instruction helpful.
  • Patti from Ozark, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
got the parts from parts select and got the machine repaired quickly
what a savings
repair man would have been over 100 dollars
the shipping was more than the parts but I saved greatly with no repairman
love your site and the great savings
i really loved my washing machine and hating to lose it
was so satisfi ed that I could save it after all these years
thanks
Was this helpful?
Thank you for voting!
Washer Agitator not working properly
1 person found this instruction helpful.
  • Carleen from Las Vegas, NV
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking th e agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix
Was this helpful?
Thank you for voting!
Agitator was free wheeling
1 person found this instruction helpful.
  • Dennis from Spring Grove, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
Was this helpful?
Thank you for voting!
agitator stopped working
1 person found this instruction helpful.
  • KENNETH from HAUGHTON, LA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this helpful?
Thank you for voting!
washer not agitating
1 person found this instruction helpful.
  • Richard from Corona, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet e xtension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.
Was this helpful?
Thank you for voting!
Worn out Cogs
1 person found this instruction helpful.
  • Leo from Yorba Linda, CA
  • Easy
  • 15 - 30 mins
  • Socket set
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
Was this helpful?
Thank you for voting!
agitator wasn't moving
1 person found this instruction helpful.
  • jose from lake forest, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person found this instruction helpful.
  • Jeff from Michigan City, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re pair man.
Was this helpful?
Thank you for voting!
Agitator stopped turning
1 person found this instruction helpful.
  • William from Canandaigua, NY
  • Easy
  • 15 - 30 mins
  • Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
All Instructions for the 110212
106 - 120 of 423