110212 Kenmore Washer - Instructions

All Instructions for the 110212
91 - 105 of 423

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace drain pump
2 of 2 people found this instruction helpful.
  • Katherine from Saint Cloud, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this helpful?
Thank you for voting!
Timing tabs securing the agitator center
2 of 2 people found this instruction helpful.
  • Keith from Mount Vernon, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round cente r cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this helpful?
Thank you for voting!
Spin cycle was way out of wack, like it was over loaded to 1 side
2 of 2 people found this instruction helpful.
  • David from VACAVILLE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, whic h you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people found this instruction helpful.
  • Tracy from CONWAY, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
washer shake hole machine from begin spin about 11/2 ' h
3 of 6 people found this instruction helpful.
  • Dieu from Houston, TX
  • A Bit Difficult
  • 30 - 60 mins
chage out part and washer still shake
Was this helpful?
Thank you for voting!
when in spin mode machine walks around the cellar
2 of 3 people found this instruction helpful.
  • john from Carteret, NJ
  • Difficult
  • 30 - 60 mins
  • Nutdriver
Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem
Was this helpful?
Thank you for voting!
Top agitator would not agitate
2 of 3 people found this instruction helpful.
  • Michael from Clarksville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy
Was this helpful?
Thank you for voting!
Replaced cogs in agitator
2 of 3 people found this instruction helpful.
  • Allen from Simpsonville, KY
  • Really Easy
  • Less than 15 mins
Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people found this instruction helpful.
  • Joseph from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people found this instruction helpful.
  • joseph from san antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Was this helpful?
Thank you for voting!
Agitator would not agitate
2 of 3 people found this instruction helpful.
  • Daniel from Beaufort, SC
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this helpful?
Thank you for voting!
All Instructions for the 110212
91 - 105 of 423