110212 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator would not agitate properly
1 person
found this instruction helpful.
-
Dawn from Little Rock, AR
- Easy
- 15 - 30 mins
-
Socket set
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the a
... Read more
gitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Read less
Was this helpful?
Thank you for voting!
Top partion of agitator turned in both directions by hand and was not driven by the motor.
1 person
found this instruction helpful.
-
Charles from Lindenhurst, NY
- Easy
- 15 - 30 mins
-
Socket set
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this helpful?
Thank you for voting!
Top of Agitator would not rotate
1 person
found this instruction helpful.
-
Depeturie from Madison, AL
- Really Easy
- 15 - 30 mins
-
Socket set
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Read less
Was this helpful?
Thank you for voting!
upper agitator not spinning
1 person
found this instruction helpful.
-
roger from Delanco, NJ
- Easy
- 15 - 30 mins
-
Socket set
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself fro
... Read more
m this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person
found this instruction helpful.
-
ROBERT from OXLY, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
top part ofagitator not turning.
1 person
found this instruction helpful.
-
Rodger from ANDOVER, OH
- Very Easy
- 15 - 30 mins
-
Socket set
Followed instructions on website video.
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person
found this instruction helpful.
-
David from KISSIMMEE, FL
- Really Easy
- 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest
... Read more
part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Read less
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Walter from Brandon, MS
- Really Easy
- 15 - 30 mins
-
Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit
... Read more
ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Read less
Was this helpful?
Thank you for voting!
worn our Agit-dogs, agitator wouldn't pull clothes down
2 of 4 people
found this instruction helpful.
-
Douglas from Wetumpka, AL
- Really Easy
- 15 - 30 mins
-
Socket set
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the c
... Read more
orrect place.
Read less
Was this helpful?
Thank you for voting!
Water inlet and valve froze and cracked
1 person
found this instruction helpful.
-
Donna from MOUNTAINBURG, AR
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Ordered and replaced the water inlet and valve assembly from this site
Was this helpful?
Thank you for voting!
Top portion of agitator not turning
1 person
found this instruction helpful.
-
James from Oldtown, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I
... Read more
also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.
Read less
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Linda from Arnold, MD
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
Read less
Was this helpful?
Thank you for voting!
Top of agitator was not working
1 person
found this instruction helpful.
-
David from Warren, MI
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Socket set
I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator doggs wore out
1 person
found this instruction helpful.
-
Glenda from FUQUAY VARINA, NC
- Really Easy
- 15 - 30 mins
-
Socket set
Followed youtube video. Great instruction.
Was this helpful?
Thank you for voting!
No problem
1 person
found this instruction helpful.
-
Luu from STANTON, CA
- Really Easy
- 15 - 30 mins
-
Socket set
That OK , easy.
Was this helpful?
Thank you for voting!