1065682 Kenmore Refrigerator - Instructions

All Instructions for the 1065682
121 - 135 of 1335

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
plastic ice cube guide installed
15 of 18 people found this instruction helpful.
  • Richard from Bloomington, IL
  • Easy
  • Less than 15 mins
Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then rec eived it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.
Was this helpful?
Thank you for voting!
icemaker quit working
16 of 22 people found this instruction helpful.
  • Kenneth from Aledo, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories ab out those guys!
Was this helpful?
Thank you for voting!
compressor clicking on and off, not cooling
14 of 16 people found this instruction helpful.
  • Frank from lincoln, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After unplugging the appliance I removed acess cover on back of fridge with a screwdriver, pulled the overload start device straight off the compressor, unplugged the red/ white factory pre-terminated conductors and replaced the bad start device. Took about 2 minutes. You must remove as much of the dust and lint from condenser element to keep this from happening again since heat will build up and fry the overload again.
Was this helpful?
Thank you for voting!
Not enough door storage
13 of 14 people found this instruction helpful.
  • Dennis from Owings, MD
  • Really Easy
  • Less than 15 mins
Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.
Was this helpful?
Thank you for voting!
ice dispenser broken
17 of 26 people found this instruction helpful.
  • sandra from mechanicsville, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically i nclined,
Was this helpful?
Thank you for voting!
Old motor was not resetting back to proper position halting ice production.
13 of 14 people found this instruction helpful.
  • Kevin from Spring, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossref erenced to new part number which was correct the first try. Thank you!
Was this helpful?
Thank you for voting!
compressor quit working
13 of 14 people found this instruction helpful.
  • Harry and Janet from Austin, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Really simple clear instructions with photos. With this the repair was quick and easy simply remove the bad relay and replace with the correct one. Great delivery time with terrific instructions.
Was this helpful?
Thank you for voting!
Cracked Crisper Drawer
13 of 15 people found this instruction helpful.
  • Jennifer from Salvisa, KY
  • Really Easy
  • Less than 15 mins
This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.
Was this helpful?
Thank you for voting!
Refrigerator quit cooling at all.
16 of 24 people found this instruction helpful.
  • Eddie from Ocean Springs, MS
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the cover for the lower part of the refrigerator to inspect the wiring and motor. I removed the switch and removed the wiring from it. The wiring just plugs in. When the new switch arrived, I just reinstalled it to the side of the motor and the refrigerator has been working fine ever since.
Was this helpful?
Thank you for voting!
Broken cup water fill on ice maker
13 of 15 people found this instruction helpful.
  • Matthew from Aurora, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt
Was this helpful?
Thank you for voting!
The water dispenser flow was very slow and the housing leaked when the filter was removed.
12 of 13 people found this instruction helpful.
  • Daniel from CAROL STREAM, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.
Was this helpful?
Thank you for voting!
compressor not running
14 of 19 people found this instruction helpful.
  • james from islamorada, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
found power up to current relay but not to compressor. removed the old current relay and installed the new relay and the compressor started running and the refrigerator works fine now.
Was this helpful?
Thank you for voting!
The ice maker stopped working
16 of 25 people found this instruction helpful.
  • Duncan from Larchmont, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repai r man. He would have made two trips since he would never have had this part with him.
Was this helpful?
Thank you for voting!
Refrigerator quit cooling, freezer defrosted making a huge mess in kitchen floor
11 of 11 people found this instruction helpful.
  • Kevin from ANDERSON, SC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First, verified power supply. I have power at wall outlet, no power at compressor. Also noticed no condenser fan operation. Searched YouTube and watched a few diagnostic videos of how to test for proper operation of my model. Dropped the control panel down to reveal the thermostat switch and control board. Wiggled thermostat knob and comp ressor would work intermittently. Thermostat bad internally. Removed wiring connections, removed cover over temp.probe. slowly removed capillary tube. Removed plastic sheath from tube. Take your time installing new capillary tube into plastic sheath as not to kink and damage tube. Route the new tube back into position that the old one was in. Reinstall covers. NOTE: My wiring terminals on the new switch were in different locations but the switch was the same dimensions. I used a multi-meter to determine the correct wire locations on new switch and installed. Reconnected power and all works well now.
Was this helpful?
Thank you for voting!
No-Refrigeration
18 of 32 people found this instruction helpful.
  • Joseph from Red Bank, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
Read the instructions that came with the relay/overload.

Determined wich of the relays and overloads in the kit supplied was needed on the refrigerator.

removed the old relay and capacitor.

Simply installed the new parts .

Back in business.

Thanks for the quick delivery.
Was this helpful?
Thank you for voting!
All Instructions for the 1065682
121 - 135 of 1335