1065682 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
plastic door shelf was cracked & couldn't hold any weight
20 of 20 people
found this instruction helpful.
-
Nancy from Hilton Head Island, SC
- Really Easy
- Less than 15 mins
looked up the model #, found your co. & ordered a new one Service was excellent, shipping reasonable; it was a pleasant surprise. I will tell my friends about your co.
Was this helpful?
Thank you for voting!
Refrigerator not cooling, water dripping from doors
21 of 24 people
found this instruction helpful.
-
Darrell from Hammond, LA
- Easy
- 15 - 30 mins
-
Screw drivers
Water was dripping out of top freezer door and had water under the refridgerator. I could hear a clicking noice from bottom of refrigerator every 3-5 minutes.
After removing back panel, I noticed the fan was running and the clicking seemed to be coming from somewhere around the compressor which was warm. I noticed on the site a si ... Read more mular problem had been submitted. It said to remove the start relay and if it rattled it was bad. I removed two wires from it ( it is connected onto the side of the compressor) then took a small screw driver to pry it away from the compressor. It not only rattled but had tiny pieces falling out. I ordered the part and replaced it in less than 15 minutes total and all is well.
After removing back panel, I noticed the fan was running and the clicking seemed to be coming from somewhere around the compressor which was warm. I noticed on the site a si ... Read more mular problem had been submitted. It said to remove the start relay and if it rattled it was bad. I removed two wires from it ( it is connected onto the side of the compressor) then took a small screw driver to pry it away from the compressor. It not only rattled but had tiny pieces falling out. I ordered the part and replaced it in less than 15 minutes total and all is well.
Read less
Was this helpful?
Thank you for voting!
Grille had permanent water marks
22 of 27 people
found this instruction helpful.
-
Chris from Plymouth, MN
- Really Easy
- Less than 15 mins
I discovered recently that the grille was removable. The protective coating had been removed because of using a scrub brush to remove hard water stains. It looked horrible and was very hard to keep clean. The new one works fantastically!! No tools required at all. I feel stupid not having done this sooner.
Was this helpful?
Thank you for voting!
The old resevoir needed to be replaced
35 of 68 people
found this instruction helpful.
-
Fred from Martinsburg, WV
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
Read less
Was this helpful?
Thank you for voting!
Refrigeator would not drfrost...
27 of 44 people
found this instruction helpful.
-
Curtis from Pikeville, KY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you
... Read more
Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.
Thank you
Curtis Hall
Thank you
Curtis Hall
Read less
Was this helpful?
Thank you for voting!
ice would not fall from ice maker
22 of 30 people
found this instruction helpful.
-
Greg from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker
... Read more
from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.
Read less
Was this helpful?
Thank you for voting!
Ice machine wouldn't dispense ice from the door.
20 of 26 people
found this instruction helpful.
-
Linda from Jackson, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the broken coupling with the new one from your store. It took less than 10 minutes. The video you provided on the website was very helpful.
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice door holder arm broken
20 of 26 people
found this instruction helpful.
-
Joseph S from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Nutdriver
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the pl
... Read more
astic arm, which caused the arm to fail. Then reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working.
22 of 32 people
found this instruction helpful.
-
Scott from Fort Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling t
... Read more
he tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Part imediately broke
21 of 29 people
found this instruction helpful.
-
STEVE from HUGHESVILLE, MD
- Very Difficult
- More than 2 hours
Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.
Was this helpful?
Thank you for voting!
motor would not turn
27 of 47 people
found this instruction helpful.
-
Arnian / from San Diego, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
removed cover the four screws that mounted the motor,unplugged and replaced motor
Was this helpful?
Thank you for voting!
Ice maker would not stop making ice (Style 2)
17 of 18 people
found this instruction helpful.
-
James from Satellite Beach, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.
Biggest problem ... Read more was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.
Biggest problem ... Read more was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.
Read less
Was this helpful?
Thank you for voting!
Unable to set the cold-control to a sufficiently cold setting.
36 of 75 people
found this instruction helpful.
-
Leo from Lewisport, KY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now ... Read more .
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now ... Read more .
Read less
Was this helpful?
Thank you for voting!
Water leaking from under refrigerator.
17 of 18 people
found this instruction helpful.
-
Ronald from DELRAN, NJ
- Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for le
... Read more
ak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.
The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.
The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped producing ice
17 of 18 people
found this instruction helpful.
-
Matthew from Austin, TX
- Easy
- Less than 15 mins
-
Screw drivers
Emiter blinking red; ice maker stopped working. Called appliance repair, said electronic control boards needed to be replaced. Quoted me $275, including parts. Ordered part at partselect.com, installed in 15 min and ice maker started producing ice. Also discovered on other online forums that this part is a common failure on these model
... Read more
refrigerators. Very easy to swap out, plug & play. Make sure to unplug appliance before performing repair due to shock risk.
Read less
Was this helpful?
Thank you for voting!