Frigidaire 134417000 - Seal | PartSelect.ca
Seal – Part Number: 134417000
( Grid squares measure 1x1 inch )
Seal – Part Number: 134417000 Seal – Part Number: 134417000 https://partselectca.azureedge.net/Schematics/Frigidaire/ZHGITR3L.gif

Seal

Your Price

CAD$55.33

PartSelect Number PS975849
Manufacturer Part Number 134417000
Manufactured by Frigidaire

Adhesive is sold separately.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse, Crosley, Electrolux.

This part works with the following products: Dryer.

This part fixes the following symptoms: Noisy | Takes too long to dry

Related Parts Additional or alternate parts to consider.

Part Photo
Description
Price
Availability
(1)
PartSelect: PS474458
Used for installing felt and rubber seals on dryers.
$51.20
In Stock
Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Customer Repair Stories

Average Repair Rating: 2.8 / 5.0, 9 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Zaya from Weaverville, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
134503600, 134417000, 5303937182, 5303281153, 137513300, 131553900
Rear bearing assembly failed and damage heating element
Removed top using a butter knife to release the two tabs in the front(between the top and the front). Removed the front(two screws from the inside. removed rear louver panel(four screws). reached in through rear panel and released belt. removed drum assembly and change out, bearing assembly drum and bushing assembly in the back panel, being sure not to forget the grounding bearing(had my 9 year old give me an extra hand to hold the ball bearing on the back..
Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for..
33 of 43 people found this instruction helpful.
Was this instruction helpful to you?
James from Hanover, PA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
134503600, 134417000, 5303937139, 5303283286, 5303281153
clothing getting cought,brown stains,noisey
watch the video first very helpful, was a lot easier than I thought.Dryer was pretty old but I figured what the heck.I replaced front lower basket seal,drum glide,dryer seal,belt,and bearing.Worst part was removing old top and bottom basket seals, a lot of elbow grease.I wouldn't have attempted it if not for the video. Dryer works great thanks partslect I will deffinitly shop here again very pleased, hope to get a few more years out of it.
19 of 19 people found this instruction helpful.
Was this instruction helpful to you?
William from Ardmore, OK
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Parts Used:
134503600, 134417000, 5303937139, 5303283286, 5303281153
Dryer was squealing and leaving brown marks on clothes.
Disconnected power and vent then pulled away from wall. You will need to move the dryer away from the wall to replace the ground bearing and retaining plate and/or the dryer belt. Removed top of dryer, disconnected wiring harness' then removed the two screws that hold the front panel on the dryer. After removing the two screws, lift out and then up on the front panel. This should remove it from the retaining clips on the bottom. To remove the dryer belt, remove access panel on rear/ bottom left of dryer. Just inside the panel you will see a tension pulley held by a spring. Use your hands to relieve the tension on the belt and remove the belt from the bottom pulleys. Now go to the side of the dryer and attempt to lift up on the front and back of the drum to remove it from the rear bearing guide. There is a slot that it rides in and it only needs to come up about an inch or so. If you cannot get the the rear bearing free this way, you will have to get inside the drum and remove the three screws in the back of the drum. There are two sets of screws, remove the inside circle of screws. At this point, the drum should slide out the front of the dryer. Use aSharpie to mark the center of the top guide on the metal then use a chisel or putty knife to remove the old guides from the front panel of the dryer. You probably won't be able to remove all of the old glue, but make sure you remove all of the old felt. Lay the panel front down and apply glue to the new top guide. Line up center of top guide with the mark you made earlier. Clamp in place. I used several spring clamps, but clothes pins will work. Now put glue on the bottom guide and clamp it in place. The bevel on the bottom guide will point to the back of the dryer. Now, while your dryer is disassembled and the glue is drying CLEAN IT OUT!!! You'll have no better opportunity to thoroughly clean this thing. Remove old bearing guide from the back of the dryer and replace with the new one. This will include the new grounding bearing and retaining plate. Apply high temp grease (generously) to the new bearing guide. Remove old rear drum bearing from drum and install new one. Take old belt off drum and put new one on. Place drum back in dryer cabinet. Be sure new belt doesn't snag or hang on anything. Guide the new rear drum bearing into the groove on the top of the guide and push down into place. It should be a snap ;-). GO to back of dryer and reinstall new dryer belt around pulleys. I put a little of the high temp grease on the guide pulley shaft on the tensioner. Replace access panel. Reinstall front panel by placing bottom back into the two retaining clips and then use your free hand to lift up the drum and guide it into place around the new guides while pushing the top of the panel into place. Replace top screws in front panel and reconnect wiring harness'. Replace top of dryer, slide dryer into place and reattach vent. Hope thos helps someone. It really wasn't very hard.
19 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Gerald from Alliance, NE
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers
Parts Used:
134417000, 5308027429, 131553900
Burned out heater element
1.Remove 2 screws and the air intake grill on the back of the unit. remove the drive belt. 2. Remove 2 screws on rear of top, slide top back and remove. 3. Remove 2 screws about a foot down on the inside on each side of the front cover. Remove four screws that secure the plastic control panel and the front panel that are right behind the control panel on the top. Disconnect the wiring harnesses, cut the nylon wire tie that is closest to the front cover. 3. lay unit on its back and and remove the two screws on the lower edge of the front panel, take your putty knife and slide it in the gap between the front panel and the dryer cabinet and release the two spring clips on both sides. Then you can lift off the front panel and control panel, set it to the side. 4. Remove the screw and the nylon guide from the center of the top front case crossmember. Remove the three screws on the inside rear of the drum, lift out the drum and set aside. 5. The drum pivot just sits in a nylon socket, pop it toward the top of the machine and lift it out, you may want to clean it good and re-lubricate it on reassembly. Disconnect the wires from the heating element and the heat sensor. 6. Set the cabinet upright and remove the four screws on the back side of the rear of the cabinet but not the two that are right in the center, they hold the pivot fixture and don't need to come out. The heater coil pan is now loose and ready for removal. 7. The seal between the filter housing and the blower housing was torn and this is an important part to have right, any air leak here will do the same thing as a dirty lint filter or plugged dryer exhaust and your new heating element will have a short, hot life. I pulled the old one off, scrapped the old glue off, applied the adhesive like the instructions on the tube say and after a few minutes installed the new seal then set the front panel to the side to let the adhesive dry. 8. The reassembly is just the reverse of the disassembly , use a couple nails or awls to help hold the dryer heater pan in place for screw installation and you might want to gentle squeeze the wire connecters if they feel loose, also check for clogged or kinked exhaust and stress the importance of cleaning the lint filter after EVERY load, it is small and all the air that cools the heating element must go through it, if is isn't maintained your new element won't last long. Have fun!
14 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Dennis from Clover, SC
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
134503600, 134417000, 5303937139, 5303283286, 5303281153
Dryer was squealing intermittently with light wash loads in it, but squeals continuously with full loads.
I followed the recommendation from William, from Ardmore, OK and Elvis, from Miami, FL for the repairs. Elvis had detailed instructions as well as William, so I just combined the two and I was able to repair my dryer in three hours time. My sincere thanks to partselect web site in posting the repairs on line and for everyones input. I will be back to use the web site again to troubleshoot my other appliances and order parts (great price, fast service for parts) and I will highly recommend this site to my friends.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Phillip from Kabetogama, MN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Parts Used:
131863007, 134503600, 134417000, 5303937139, 5303281153, 131553900, 131302800
did'nt heat, dryer squealed very loud
I googled and found parts select, listed model make and found parts diagram, found suspected parts from trouble shooting blog. I read repair stories, people who performed identical repairs, followed their lead, made notes ordered parts and
easily repaired my dryer for a fraction of the cost of replacing dryer.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
john from Oak Park, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
134417000, 5303937139, 5303283286, 131553800
Clothes getting caught in the drum and getting rust stains
Looking from the front at the top cover I lifted the cover with my fingers and inserted a screw driver about one or two inches from each edge.
The top pops loose and lifts up like the hood of a car.
Inside the dryer on either side behind the front panel there is one screw on each side. Remove the screws and lift the entire panel and door. Then swing the assembly out like a door with a hinge on the right. It won't come off due to the wiring harness.
Make sure you study the upper drum glide before removing it. Remove the upper drum glide using Acetone, this is easy but a little messy.
Apply glue, I applied to the drum but if I did it again I would apply it to the glide and clamp it to the drum in three or four places.
This is an income property and my tenants weren't happy so I didn't wait for the other parts. I don't know now if I really needed them. I will replace them anyway.
I realize they make these things easy to repair. It makes the $200+ they charge that much more profitable.
I also vacuumed and cleaned inside.
This is pretty easy and does not require much skill.
Position the panel on the dryer. There are two clips that need to lined up on the bottom and fit the drum back on. Then snap the top cover in and test the dryer.
Remove the top replace the front panel screws and snap the top back in.

I wish I could post pictures there really isn't much to it.
For property owners I would recommend learning how to do this prior to getting a call.
Create a kit of parts that will wear or break. $100 will save you the hassle of ordering under pressure and get you up and running that much faster.
1 person found this instruction helpful.
Was this instruction helpful to you?
Richard from Santa Rosa, CA
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set
Parts Used:
134503600, 134417000, 5303937139, 5303283286, 5303281153
clothes got burn marks
After pulling out and unplugging my machine I followed the procedure already worked out by others. I bought and replaced all the parts that were listed as involved with this problem, since I only wanted to do this once and the parts were pretty cheap. The only slightly hard part was reconnecting the drum to the bearing, this could be easier with a third hand.Everything went well and the dryer works fine.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Sarah from Stillwater, MN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Parts Used:
134503600, 134417000, 5303937139
dryer was leaving brown stains on clothing
The directions for repair were easy and straight forward.
The repair was quick but extra time was needed for the adhesive to dry. The dryer has been working like a charm ever since, although it seems slightly out of balance now and makes a squeaking noise while turning. I checked the adjustable feet and one is stuck. Seem like a quick liquid wrench project.
0 of 5 people found this instruction helpful.
Was this instruction helpful to you?

Model Cross Reference

Brand
Model Number
Description
Frigidaire
41749012890
Dryer - Residential, Electric
Frigidaire
41749022890
Dryer - Residential, Electric
Kenmore
41759012890
Dryer - Kemore Dryer 41759012890
Frigidaire
41759022890
Dryer - Gas
Kenmore
41764182300
Dryer
Kenmore
41769042990
Dryer
Kenmore
41769042991
Dryer
Kenmore
41769052990
Dryer
Kenmore
41769052991
Dryer
Kenmore
41774182300
Dryer
Kenmore
41774182301
Dryer
Kenmore
41779042900
Dryer - Kenmore Dryer Model 417.79042900 (41779042900, 417 79042900) Parts
Kenmore
41779042990
Dryer
Kenmore
41779042991
Dryer
Kenmore
41779052990
Dryer
Kenmore
41779052991
Dryer
Kenmore
41780032990
Dryer
Kenmore
41780042990
Dryer
Kenmore
41780042991
Dryer
Kenmore
4178005291
Dryer - Kenmore Dryer Model 417.8005291 (4178005291, 417 8005291) Parts
Kenmore
41780052990
Dryer
Kenmore
41780052991
Dryer
Kenmore
41780142000
Dryer
Kenmore
41780412700
Dryer
Kenmore
41781042000
Dryer
Kenmore
41781042001
Dryer
Kenmore
41781052000
Dryer
Kenmore
41781052001
Dryer
Kenmore
41781142000
Dryer
Kenmore
41781142001
Dryer