First, I unplugged the dryer. Then, I removed the back panel from the controls section (6 screws), disconnected the old switch and reconnected the new switch. Positioning the switch in the control panel took some figuring out, but once I realized that the switch slots into place, and then gets locked in by turning 1/8 of a turn, it worked fine.
Replacing the knobs was a cinch, just popped them in place. Now the controls are like new again.
Frigidaire controls are really junk, though. I won't be surprised if I have to do this repair again in two years.
1st. unplug dryer 2nd. remove housing / 4 allen head screws 3rd. remove wiring clips from switch 4th. remove switch / install new 5th. install wiring clips 6th. test dryer 7th put housing back on
Knob fell off - start switch shaft broken from pliers
Unplug the dryer!! I warned my partner of this at first, but she didn't listen.... got quite a little shock from the wires. Removed the back panel with a phillips head screwdriver, removed the connecting wires from the starter box. One was a bit snug, so I loosened it with some flat-nosed pliers. Twisted the unit and it popped right out! Once the part came in I popped it back in, twisted it until it locked into place, put the connecting wires on and replaced the panel. The knob snapped on easily and it all took about 10 minutes total to do! I'm not much of a repairman or electrician and this was SUPER easy!
First I removed the existing knobs and then the screws holding the top panel. I then removed the broken switch and replaced it with the new one, replaced the panel and knobs. The process took me approx. 45 minutes. PartsSelect.com saved me the cost of hiring a handyman.
First I unplugged the dryer. I removed the 3 knobs on the front control panel as well as the 6 screws on the back. The start switch easily removes by turning it 45 degrees and pulls out. I used a pair of needle nose pliers to pull the two connectors loose from the old switch. (They are color coded wires, 1 brown and 1 gray. The switch is marked with the numbers 1 and 2 on the connectors so remember which one goes where) Then i hooked up the new switch in reverse order and was back in business in about 5 minutes.
Other Parts Used:
James from Baton Rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the turn start switch and had to replace it
This was a Sears Dryer, also know as Kenmore, This dryer can be stacked or side by side. In this case it was stacked. There are no directions on how to replace this part. For this model made in 2005 the lid of the dryer is held in front by two clips. You open the lid simply by prying the two front corners up with a flat head screw driver. The front of the top lid pops right up. You may have to remove the mounts in back if you cant lift the dryer lid enough to be able to get your hands in. UNPLUG THE DRYER I got a nasty shock. There are two wires on the switch, remember how they go and where they are, that's important. Turn the switch (from the front or back) so that it pops out. Remove and replace the wires put it back in (from behind/top) and twist a 1/4 turn into place. Plug, test and simply push the cover back down onto the clips. Done.
Other Parts Used:
Don from Port Jefferson, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Start Button broke in the unit
I unplugged the dryer from the wall and removed the back panel to replace the switch. It only had two wires on the switch I pulled then off and placed them on the new switch and put the unit back together and replaced all the knobs with new ones and it looks new again. Thanks to Parts Select.
I broke my switch that turn the dryer on and I also broke the knob
I watch the video and did exactly what the video say , the video was 3 minutes and I can't remember how many seconds long I repaired it in 3 minutes or less
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
October 10, 2017
Is there a video that shows out to install the start switch(ps975832) are there instruction with the switch
For model number FGRB7800DS0
Hi James,
Thank you for your question. Yes we do. Here you are: https://youtu.be/FaExCHwWFO8 . Good luck with your repair.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Phyllis
November 4, 2017
What is a thermal limiter.
For model number GLER331AS1
Hi Phyllis, Thank you for the question.The thermal limiter, also known as a thermal fuse, blows to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts out. If the thermal fuse is defective, damaged, or blown. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mary
March 19, 2019
The switch you push to start the dryer won't works. I can select the cycle i want.
Hi Mary, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. You may also want to check your start switch itself. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Henry
October 27, 2021
I ordered this part on Monday for next day delivery, two days later still haven't received, just trying to track package.
Hello Henry, thank you for writing. This service is meant for part inquiries, installation help, and other such questions. If you have an order with our company and need to speak about that, you will have to contact our customer service. You can do so one of two ways: email: customerservice@partselect.com, or telephone: 1 888 260 4310. Thank you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
January 1, 2018
Our dryer overheated and shut off. Cooled down, and it starts to run when you turn the start switch but stops when you release the switch. Is this likely a bad start switch or something else?
For model number GLER331AS2
Hi Steve, Thank you for the question. if the appliance over heated the start switch is not the issue. I suggest cleaning out the vents and the vent tubes. Make sure they are sitting flat with no dips or bends. If the air flow is blocked it will cause the appliance to over heat. it is also a good idea to remove the front panel and clean any lint build up from the duct and inside the cabinet. Once everything is cleaned out and if you have the same issues, you will need to test the thermostats and the thermal limiter on the element housing and the blower housing to see if they are defective or where tripped when they over heated. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Zarinah
March 16, 2018
Ps975832 is this the correct part for my model? I need to replace the knob and the switch base. Thank you
For model number GLWS1339CS1
Hi Zarinah,
Thank you for your question. Yes, this would be the correct start switch for your washer. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Harry
April 7, 2023
Hello,
If my switch is bad , would I hear a buzzing noise when I turn the switch, on?
Or could it be something else?
thanks
For model number GLER341AS1
Hi Harry, thank you for contacting us. Based on our understanding of the issue, we would suggest you check the power supply to your dryer. Sometimes, a tripped circuit breaker might stop enough power from getting to the dryer, causing a buzzing noise. If the issue remains, the problem might be with the door switch, part number PS2330880. The door switch tells the main control board that the door is closed, and it can allow the dryer to run. When the switch becomes faulty, your dryer might not start at all, and it will make a buzzing noise. We would recommend checking the door switch for continuity using a multimeter. We hope this information helps!
May drier was working fine last evening now this am it doesn’t turn on.? any idea what i should start to look at
For model number GSE746RFS3
Hello Sandra, thank you for your inquiry. Attached is a link that will help with your inquiry. Thank you.
https://www.partselect.com/Repair/Dryer/Will-Not-Start/
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS975832
Manufacturer Part Number: 134398300
