Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noise and Squeaking from Front During Drying
Front roller bearings were bad and figured to do the belt while in there. I bought the manual online which was very helpful. ?? Unplug dryer Remove 4 screws behind touch panel Tilt panel forward then up leaving wires attached Rear has 2 screws on the rear ends facing down remove them at ends Lift rear up then forward push and top will be freed (keep on top) Front edges have 1 screw each but sharp areas watch Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place Wires for light and switch can stay attached, move front/door to side Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place. To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove) Remove x 4 small screws..... hold drum inside then lift brace up and forward Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum. Reverse the steps..
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Angel
February 6, 2019
When i push the start button, the dryer won't start. It make the noise like is going to but, the drum itself won't spin or turn. I have to spin or turn the drum manually for less then half of a turn in order to works!. i was thinking it could be the drive belt? what seem to be the possible diagnosis, thanks.
For model number DPGT750EC1PL
Hello Angel, Thank you for contacting us. I suggest checking the following part: PS959860 Latch Hook. Good luck with your repair!
Was this helpful?
Thank you for voting!
Bill
February 15, 2022
What length is the dryer drive belt?
For model number DPGT650EH0MG
Hello Bill, Thank you for the question. Very sorry but we do not have the dimensions for this, however we have researched the model you have provided and have confirmed the part you are looking for is PartSelect Number PS959966 and is a guaranteed fit. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Kathy
June 4, 2022
Need Heat Element Kit
For model number PTSD850EMOWW
Hi Kathy,
Thank you for your question. The part number listed under your model number for the heater assembly is PS3499685. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
This part is the replacement drum support roller for your dryer. The roller is approximately 3 inches in diameter and is sold individually. The main reason to replace the drum support roller is if the bearings have worn ...
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Our scratch-free, streak-free formula removes fingerprints, smudges, grease, dirt and oil, while protecting and polishing to repel dust and dirt. Use on all stainless steel appliance brands and surfaces. Stainless Steel ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS959966
Manufacturer Part Number: WE12X10011