Part Location Diagram of 4280EN4001C LG BEARING,BALL
See part NI in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

BEARING,BALL

★★★★★
★★★★★
1 Review
$80.98
  On Order
PartSelect Number PS7785069
Manufacturer Part Number 4280EN4001C
Manufactured by LG
Product Description

BEARING,BALL Specifications

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy and Marks Left on Clothes
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
LG, Kenmore.
Part# 4280EN4001C replaces these:
4280EN4001M, 4280EN4001T, 4280EN4001X, 4280FR4048L, AGF76083930
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.5 / 5.0, 6 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Bearing seal out causing bearings to get wet and very noisy
Watched a short video to figure out to remove panels. After panels were off I removed as much as I could from the inside of the machine. This was not completely necessary however for an extra half hour it made inspection, cleanup and removal of tub housing out the front of the machine much easier. Once out, I split the two halves of the outer basin and sprayed the spider shaft with penetrating oil. Using a brass drift I did have to get a bit aggressive to drive spider shaft out, then I used a heavy metal punch to hammer out the bearings. For those who may not know using brass or a soft metal will keep from damaging reusable parts. At this point it was cleanup time, with dish soap I scrubbed the two halves of the outer basin and the wash basin itself then used emery cloth on the bearing casing and spider shaft. I am a firm believer if u take the time to cleanup properly things go back together much easier. At this point I began to reassemble, replacing tub bearings and seal, the wash basin then putting the two halves of the outer basin back together. I strongly recommend replacing gasket for the halves of the outer basin, for as much as it takes to get there it is money well spent to up the chances of a leak free system. Now with the wash tub back together it was time to reset the tub and hook everything back up. I skipped a lot of steps but if a person pays attention, takes pictures if they have to, even numbers lines with a sharpie it is a very easy repair. Very easy but very time consuming. I am DIY’er, in all I spent about ten hours over two days to do this job. Thus being said I am very particular spent a lot of time cleaning, scrubbing looking at as many wear points and checking for rubbed wires. Hope this helps someone out there, definitely not a strong writer or like doing it. Oh one other thing, I ordered the shocks on the bottom side of wash tub just because I guess not thinking they were bad just thinking I could help tune it up. Was surprised to find the old ones were completely shot, was glad I ordered new ones. After repairs, noise is gone and machine is quiet again. Thank you, your website is very easy to find parts and order.
Other Parts Used:
Locking Pin BEARING,BALL Gasket Rear Tub Gasket Shock Absorber Kit
  • Todd from STOCKTON, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
67 of 70 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise, especially during the spin cycle.
First I watched several videos on YouTube, numerous times. When I started to disassemble the washer, I put the parts I removed on the floor in the work area in the order I removed them. I also took a couple of photos of where wiring and hoses went so I would have a reference the next day (I took parts of two days to complete the repair).When I removed fasteners (screws, etc), I labeled them as to what part they went with, making re-assembly easier and faster. The most difficult part was re-installing the wire retainers on the door bellows (make sure you use some liquid dish detergent as lubricant). The results were great, I have a like "new"washer now.
Other Parts Used:
Washer Tub Bearing, Rear Gasket Rear Tub Gasket
  • Richard from CUMMING, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very nosey
Replace both bearings and seal also replace spider gear due to the bearing seal surface damage,also replace drum gasket and door gasket and all shock absorber.The clean up two more time then the repairs did.
Other Parts Used:
Washer Tub Bearing, Rear LEG ASSEMBLY Rear Tub Gasket
  • Lonnie from JACKSONVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very noisy when tub was spinning , tub bearings and seal were bad.
Watched a YouTube video on how to disassemble the washer step by step, replace the bearings, and reassemble the machine. was very helpful.
Other Parts Used:
Washer Tub Bearing, Rear Gasket Rear Tub Gasket
  • Gerald from CENTRALIA, KS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad/worn drum bearings
Followed the step-by-step video, you end up taking most of the washer apart. Got the drum out & apart, then ran into a wall with the bearings. Couldn't get them out - acted like the housings were frozen. Took all the pieces of the washer to the curb for garbage pickup.
I never opened the replacement parts and will be returning them.
Other Parts Used:
Washer Tub Bearing, Rear Gasket Rear Tub Gasket
  • Michael from DUBLIN, OH
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum was making a very load grinding sound
I took the washer completely apart and ordered any parts that looked worn and put it back together. It’s working like new and will last for a few years
Other Parts Used:
  • willard from RIVERSIDE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donald
July 5, 2021
When replacing the rear tub bearing should any other parts be replaced? Can bearing be replaced or should tub assembly be replaced? What is bearing part # and cost and what is rear tub bearing assembly part # and cost? Thank you. Don
For model number WM2277HB
PartSelect logo
Hello Donald, Thank you for the question. When replacing the Bearings we also suggest replacing the Rear Tub Gasket. We hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Casey
November 3, 2023
There are two bearings in the back of the washer. Do I need to order two or do two bearings come with 1 order?
For model number 79641182311
PartSelect logo
Hello Casey, Thank you for the question. This model lists one Ball Bearing Part #: PS7785069 and One Ball Bearing Part #: PS11711138. The Bearings are sold separately. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS7785069
Manufacturer Part Number: 4280EN4001C
Brand
Model Number
Description
LG
40311
Washer - Washer
LG
40318
Washer - Washer
LG
40441
Washer
LG
40518
Washer - Washer
LG
41028
Washer - Washer
LG
41029
Washer - Washer
LG
41172
Washer Dryer Combo - Washer-Dryer
LG
41182
Washer - Washer
LG
41272
Washer - Washer
LG
41372
Washer Dryer Combo - Washer-Dryer
LG
41373
Washer Dryer Combo - Washer-Dryer
LG
41383
Washer - Washer
LG
41572
Washer - Washer
LG
41682
Washer - Washer
LG
41722
Washer - Washer
LG
41729
Washer Dryer Combo - Washer-Dryer
LG
41962
Washer - Washer
Kenmore
79640272800
Washer
Kenmore
79640272900
Washer
Kenmore
79641002610
Washer - Kenmore Washing Machine 79641002610
Kenmore
79641003610
Washer - Kenmore Washing Machine 79641003610
Kenmore
79641172210
Washer - WASHER
Kenmore
79641172211
Washer - WASHER
Kenmore
79641172212
Washer - Kenmore Washing Machine 79641172212
Kenmore
79641182310
Washer - WASHER
Kenmore
79641182311
Washer - WASHER
LG
79641272211
Washer - Lg Washing Machine 79641272211
Kenmore
79641282310
Washer - WASHER
Kenmore
79641282311
Washer - WASHER
Kenmore
79641372210
Washer - WASHER
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service