79641182311 Kenmore Washer - Overview

Diagrams for 79641182311

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$138.95
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(111)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$67.05
In Stock
Washer Hose with Bellows – Part Number: 4738ER1004B
$53.85
In Stock
SENSOR ASSEMBLY – Part Number: 6501KW2002B
$53.85
In Stock
SENSOR ASSEMBLY
★★★★★
★★★★★
(19)
Part #6501KW2002B
This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating this data to the electronic control board, it ensures proper spin and agitation cycles. A malfunctioning sensor may result in the washer pumping but failing to spin or agitate, leading to incomplete wash cycles. This part is sold individually and is compatible with select washer models. For safety, always disconnect power before beginning installation, and verify model compatibility prior to purchase.
Magnetic Door Plunger – Part Number: AGM73610701
$67.05
In Stock
Door Boot Seal – Part Number: MDS47123602
$214.91
In Stock
Door Boot Seal
★★★★★
★★★★★
(11)
Part #MDS47123602
This door boot seal is for front loading washing machines. This part forms a seal between the wash tub and the door, preventing leaks. We recommend unplugging the washer before installing this part and wearing work gloves to protect your hands.
Shock Absorber Kit – Part Number: 383EER3001J
$57.15
In Stock
Rear Tub Gasket – Part Number: 4036ER2004A
$47.25
In Stock
Inlet Valve Assembly – Part Number: 5221ER1003A
$93.03
On Order
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
$39.55
In Stock
Clamp Assembly – Part Number: ACA56078801
$26.65
In Stock
Washer Hinge Spring – Part Number: 4970FR2084Z
$54.95
In Stock

Questions And Answers for 79641182311

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jay - For model number 79641182311
April 16, 2023
drum seems to tilt back not sure but spins free gave load clunk then went off balance
Chris Boyle Profile
Hi Jay, thank you for reaching out. You may need the shock absorber kit, part number PS3522313. We hope this helps!
$57.15
In Stock
Shock Absorber Kit
Was this helpful?
Thank you for voting!
Jim - For model number 79641182311
February 14, 2024
The door lock frame is bent in just a little. I need to know how to move the rubber gasket between the door and tub?
Chris Boyle Profile
Hello Tim, Thank you for writing. We were able to locate one of our How to Videos. The part and appliance might be slightly different; however, they will have the same basic steps for instillation. We hope this helps with the repair!
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 79641182311

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
LE Error Message and won't spin drum properly
255 of 339 people found this instruction helpful.
  • Mark from Harrisburg, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Was this helpful?
Thank you for voting!
Door would not close
157 of 181 people found this instruction helpful.
  • Omnitech from Warrenville, IL
  • Really Easy
  • Less than 15 mins
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
Was this helpful?
Thank you for voting!