The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Washer Lid Switch with Wire Harness
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Will Not Start | Will not drain
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WH12X10334 replaces these:
AP3968471, 1256927
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
4.8
Filter By Rating:
5 Stars
3
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Alexis G - November 8, 2018
Verified Purchase
Perfect!
Easy repair, exact part as needed. Thanks!
★★★★★
★★★★★
Simon L - September 14, 2021
Verified Purchase
Great deal!
Part goes perfectly. My washer finally work!
★★★★★
★★★★★
Dan T - November 3, 2021
Verified Purchase
Lid switch repair part
The part was shipped very quickly and everything is up and running now
★★★★★
★★★★★
Dorothy W - August 12, 2023
Verified Purchase
Quick delivery
Received part quickly. Was able to fix washer at home.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 17 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
washing machine would not go through all cycles or agitate
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Other Parts Used:
Brian from Millerplace, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
229 of 290 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer didn't wash/spin
Replaced lid switch with wire harness. Video available on this web page. The technician said bad motor. We counted the flashes, light on top of motor, was 7 times. Diagnoses are very important, save you money! Do it more times, be sure. Biggest problem is socket size for the screws, size 6,5mm or 1/4 inch. Do not call technician or throw away your washer!...
Other Parts Used:
Eva from NAPLES, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
14 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin
Removed front panel, cut two wires to switch ( color coded ) snapped old switch out and installed new switch, connected wires with wire nuts. Removed two screws in lid, removed magnet and installed the new one. A caveman could do it!
Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success
Other Parts Used:
Joseph from Manchester, NH
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
10 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin the water out of the clothes.
I wasn't sure what the problem was. I Googled the most common problem for this washer and it pointed to the Lid Switch with Wire Harness. I ordered the part, watched the video provided, and installed it. Installation was just like the video said. Due to the lack of dexterity in my hands due to arthritis, it took about 25 minutes from start to finish. Washer works like new now.
Ordered lid switch from parts select via website. Two days later I received the part in the mail. Instead or re-wiring, I cut wire close to existing bad switch. Splice two wires and cap with wire nuts. Zip tie loose wire to tub housing.
Other Parts Used:
Tommy from MALVERNE, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not spin .
First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen
Other Parts Used:
MAUREEN from ABINGTON, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin
I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .
Other Parts Used:
Don from BREMERTON, WA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Machine will do everything and stop at the last spin, will not spin at the end.
I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.
Other Parts Used:
Nelson from LARGO, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
31 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Louie
October 30, 2017
Washer fills and agitates, goes through wash cycle, drains but will not spin. Hums for a while, then indicator light goes off. Humming continues. Already tried changing the control panel. Did not solve the issue. Could it a faulty lid switch? Thank you for you help.
For model number GTWN4950L0WS
Hi Louie, Thank you for the question.If the washer is not spinning replacing the lid switch could solve the problem.The switch acts as a safety mechanism to prevent the washer from spinning when the lid is open. If the switch is defective, the washer will think the lid is open and will not start the spin cycle. Hope this helps!
20 people found this helpful.
Was this helpful?
Thank you for voting!
Marc
August 31, 2017
Power on, hit start, tub filled and then nothing. Still got power, tub full, lights on front panel but it won't spin.
For model number GTWP2250DOWW
Hi Marc,
Thank you for your inquiry. Where your washer will not start, the most common part that will fix the issue is the lid switch. Some other parts you may also have to check are the electronic control board, the magnet assembly, and the drive belt. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Gerald
August 25, 2017
Machine doesn't start when i press the start button. I replaced the lid magnet & still doesn't start. Please advise next move.
For model number GTWN4250D1WS
Hello Gerald, thank you for contacting us. It is possible that it could be the lid switch. The pin on the lid switch pushes onto the lever of the switch to communicate to the machine that the washer lid is closed. If your washing machine is not running when the lid is closed, not spinning, draining, or agitating, replacing the lid switch could solve the problem. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Bill
April 27, 2018
Pumps out but will not spin.
For model number HSWP1000M3WW
Hello Bill, thank you for your question. If the unit is going through the fill and drain cycle, but is not agitating or spinning the first part you should replace is Lid Switch with Wire Harness Part Number: WH12X10334. This is the most common issue when dealing with your issue. I hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Pat
March 27, 2018
GE top washer... when lid is closed only cold water flows and washer goes thru complete cycle as normal.. when lid is open hot and / or cold water flows dependent on what was selected and stops after fill.. check intake valve ok hot /cold and warm works ok
For model number GTWN4250D0WS
Hi Pat,
Thank you for your question. It sounds like it might have something to do with your lid switch. I would suggest taking a look and testing this part to see if it is working correctly. I hope that helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Bob
July 24, 2017
Won't agitate or spin, but water is exhausted. I'm not sure a new switch would solve the problem, since the machine makes some sound when it is supposed to agitate or spin. Should i buy the assembly and give it a try, or do you think it might be something else? Thanks.
For model number WJSR4160G2WW
Hi Bob,
Thank you for the great question. Normally if it was a switch you would not have sounds like it was trying to agitate. Checking the list of symptoms I suggest checking the belt, part number PS1482278. If you enter this part number into the search bar on our home page you will come up with a video on how to install the new belt, watching the video will show you how to get to the belt so you can check to see if it is broken or wore out and needs to be replaced.
Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Allan
February 15, 2019
How do i test the lid switch on the washer?
For model number WHRE5550k2WW
Hello Allan, Thank you for the question. You can test the continuity with a multi meter, replace if the switch has no continuity. Thank you for your inquiry, good luck with this repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Linda
June 17, 2019
Machine works ok thru the cycle until it gets to "rinse", then stops. Could it be the lid switch or the timer?
For model number GE WWSE5240G0WW
Hello Linda, thank you for inquiring. For this symptom it is most likely this Lid Switch with Wire Harness part PS1482372 for your model.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Nicole
November 25, 2017
When the washer is plugged in and you turn the dial, all the lights turn on but nothing happens when you push the start button.
For model number GTWN4950L1WS
Hi Nicole, Thank you for the question. This sounds like an issue with the start switch or the timer switch. Both are built into the control board, so the board will need to be replaced,PartSelect Number PS3507656. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Paula
October 7, 2017
Machine will fill with water and tub will spin but when it gets to the washing stage it stops and the machine just hums.
For model number GTWN4250D0WS
Hi Paula, Thank you for the question. If the machine is not go through each cycle I suggest replacing the Timer. The timer on this model is actually built into the Electronic Control Board,Part Number: PS8757105. If the lid switch was the issue the appliance woudl fill and agitate and go through the wash cycle but when it came time to spin out, the appliance would stop.Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1482372
Manufacturer Part Number: WH12X10334
