This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ron H - September 19, 2019
Verified Purchase
Easy fix but ...
The part was a easy install, but it had to be Installed through the back unlike the video. I have ordered parts here before and they were shipped well protected this time it was just shoved in a box with no protection I am kind of disappointed
★★★★★
★★★★★
Monica Y - May 17, 2019
Verified Purchase
Great
Perfect fit
★★★★★
★★★★★
Graham S - November 13, 2018
Verified Purchase
Perfect fit and easy repair
Very pleased with the pump I received as a replacement for the one in our Amana washer. Installation was quick and easy and the pump was a perfect match for the old one. This is my third order with this company and so far every time the service has been fast and the part correct. Would definitely recommend this company to anyone looking for appliance parts and help with repairs.
★★★★★
★★★★★
JAMES K - February 16, 2022
Verified Purchase
Couldn't be easiet
The part was a perfect fit for my washer, simple install and is working great, good value compared to a new machine
★★★★★
★★★★★
Ron O - October 2, 2018
Verified Purchase
pump replacement
Part arrived next day, part was the right one, good service from this company.
★★★★★
★★★★★
Tom R - April 24, 2020
Verified Purchase
Went like clockwork
The pump was a perfect fit, the hoses switched over well. The only thing was it said, "there will be a little water in the hose". It was more than I expected, but not too big a flood. Thanks for the good service, Tom.
★★★★★
★★★★★
Laurie M - July 31, 2020
Verified Purchase
Worked perfect
The part came quickly and easily installed and it worked great!!
★★★★★
★★★★★
Perry D - June 5, 2019
Verified Purchase
very easy repair
replacing the drain pump was very easy, remove back access panel, three bolts and two clamps and it's out, and in reverse the new one back in. thanks
★★★★★
★★★★★
Scott F - November 11, 2020
Verified Purchase
Perfect part and repair
The PartSelect website made it possible for us to diagnose the problem with our washer, order the correct part and see how to do the actual repair. We were also very pleased with the quick order fulfillment. Another delighted customer.
★★★★★
★★★★★
Erin J - August 5, 2020
Verified Purchase
Exact fit
Product was the exact same size and model that we needed for replacement. Shipped within a day, at my front door within 2 days. Great service!
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 49 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!!
Other Parts Used:
kevin from rochester, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
120 of 134 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Skreeching noise during spin cycle
Pulled out washer, laid on front, removed access panel and the pump was right there. Three screws with 5/16" nut driver, pliers to release hose clamps, remove hoses, remove belt from pully, remove old pump. Install new pump with three screws, two hoses and clamps, finally put belt on new pulley and other small pulley and used screw driver shaft to pull belt on to large pulley. replace access panel, put washer back in place. It literally took me more time to clean the floor under where the washer was than to change the part. Piece-o'-cake.
Other Parts Used:
Robert from Mesa, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
65 of 66 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bearing had some kind of metal (couragated) piece that worked it's way loose and was hanging up on the pump housing or retaing plate.
Removed the old pump,- disconetced the two hoses, and 3 retaining screws, sliped off the drive belt,. installed the new pump! simple!
Other Parts Used:
Kathy from Wellington, KS
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
52 of 58 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bad water pump
shut off supply lines, remove cover on back of washer, remove drain hose from pump,inlet and exit. remove belt underneath washer from pump. remove 3 assembly screws. remove pump. set new pump in place. rescrew pump to washer. reatach inlet and exit hoses to pump put belt back on under washer put cover back on back of washer. turn supply flines back on. should work like new
Other Parts Used:
Esther from Big Run, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
34 of 34 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unit starting making terrible noise and shut down.
After examining the diagrams online, I removed the 3 screws holding on the back panel. Nothing seemed wrong so I tilted the machine to look underneath at the belt. All seemed OK but manually moving the belt by hand revealed that where the belt drives the pump had worn loose and was the source of the problem. Reading other descriptions of the ease of replacement of the pump, I ordered the new pump. It took approximately 15 minutes to remove the old pump and 10 minute to install the new pump and replace the belt. The machine is back to working fine. This is a fairly simple repair.
Other Parts Used:
Rick from Lawrenceville, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
26 of 27 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearings on the water pump self-destructed.
I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.
Other Parts Used:
Richard from San Antonio, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
20 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water intermittently leaking from bottom of washer
I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.
Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.
Other Parts Used:
CHERYL from HUDSON, NH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
15 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud hi pitched squeeling noise all the time.
Remove front panel and back service panel below water conn. lines. Put a 4" plastic box between the tub and inside of cabinet "directly opposite the spring to be removed to lower the tub to base for less opposing travel to unlatch spring from tub hook. Also took an old slotted screw driver w/ a blade about 1/4 " and grinded 1/8 from middle about an1/8" deep and used it to latch the spring when pushing it up and off the tub. Replaced all 6. Also did motor pivot spring. Tested and the it worked for one cycle, then the tub again just falls to the right as if the spring at 9 o'clock was broke and strains the belt drive but the spin cycle still works o.k. and the washer does not bang and walk away till you stop the machine. Thought the 6 tub springs would take care of both problems. Told that the snubber ring needs to be replaced. Never but another maytag again. JUst did the belt,a week later the water pump went then the springs.....
Other Parts Used:
Patrick from Accord, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
15 of 20 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
September 12, 2017
My washer is grinding noisy when agitating. I removed the belt and turn each of the three pulleys i found underneath. The only one where i felt resistance was the pump pulley. Do you think i am on the right track if i replace the pump? Thank you.
For model number MAV408DAWW
Hello Joe, thank you for contacting us. Yes, that does sound like it is the drain pump , this should be moving freely so may be time to replace. Good luck with the repair!
24 people found this helpful.
Was this helpful?
Thank you for voting!
Lenin
December 16, 2017
My brother was using the machine to wash a pair of pants and a short while after that it was smelling like burning, and he disconnected it after I arrived home. I connected it again and tried to drain all the water left behind and it was making a noise like a grinder. I have not checked under yet, so do you think I need just the belt, or the pump too?
For model number Pav3360aww
Hello Lenin,
Thanks for your question. The drive belt is the most common reason why this burning smell would occur, but the drain pump would explain the noise better. You may wish to get both parts and see if the belt fixes your issue, and then try the pump if it does not fix your issue.
I hope this helps.
Biggest problem is that the clothes will not spin out very dry. Usually a heavy load will spin out better. On a light load the clothes are very wet. I replaced the belt, pulley and shims. Tried the water pump no change. Does on occasion make some noise, wife says, i haven't heard it.
For model number MAV8557AWQ
Hello Mark, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: drain pump, motor, lid switch and hoses. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Jason
November 12, 2019
I bought a replacement pump from y’all and it doesn’t have the metal plate mounted to the pump like the one that was on my washer. How do i pull the pulleys to install the metal mounting plate to the new pump?Thanks jason
For model number Maytag MAV7260BWW
Hello Jason, thank you for your question. This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed. Good luck with your repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Terry
March 6, 2020
Machine was running rough and loud on spin cycle. I replaced the transmission pulley and bearing. The unit runs good while washing, but still loud on the spin cycle. There are no leaks, or any excessive vibration. I am wondering what part i may need. I see noise most probable cause is the water pump, but do not want to just keep replacing parts without knowing if it is actually in poor condition. Looking for some help and guidance here. Thanks, terry
For model number MAV9501EWW
Hello and thank you for writing.
Before considering changing the pump, you should check the following parts for physical damage as they are more likely to cause this issue than the pump itself:
Drive belt PS11739438
Snubber ring PS11738845
Motor pivot spring PS11739525.
We hope this information helps. Please contact us anytime if you require further assistance.
I need to replace the pump on my washer. It will spin and nothing comes out. I see you list 2 different pumps. Will they both fit or is there a specific one based on my serial number.Thanks
For model number PAV2300AWW
Hello Brian, thank you for inquiring. This Drain Pump part PS11741803 is the correct replacement for your model. It should fix both the issues of not filling with water or or not draining water.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Scott
December 28, 2017
Washing machine shakes during spin cycle after tub water drains and spinning of clothing continues. I replaced the suspension springs (all 6) along with the snubber ring. I also re-leveled the washing machine. That is the three most common fixes for a shaking machine. However, machine still shakes once water empties during the spin cycle. I checked the balance of the load and it is fine. It shakes even with a small load. During the repair, i did notice a strange situation. If the front panel is left off the machine and you put in thru a spin cycle, the machine does not shake, but the tub can be observed shaking/vibrating. When i place the front panel back on the machine, the entire machine shakes/vibrates severely. What else could be causing this since i already did the three top repairs of replacing the 6 suspension springs, the snubber ring, and re-leveling. I'm very confused as to what could be causing this issue.
For model number MAV7557EWW
Hi Scott,
Thank you for your question. If your washer is shaking and moving and you have replaced the 3 main parts in our symptoms list, then I would check the transmission and seal to see if that is causing the issue. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lynn
January 30, 2023
The washing machine did not drain before the spin cycle. The spin cycle started and threw water everywhere. No idea what part this may be.
For model number MAV7700AWQ
Hello Lynn, thank you for your inquiry. The first thing to inspect is the drain hose, part number PS11739436. If the drain hose is clogged or bent, water won't be able to flow out, which will leave all the liquid in the tub. If that does not take care of the issue, we would suggest checking the drain pump, part number PS11741803, and Drive Belt, part number PS11739438. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
My washer is spinning, but clothes are very wet at the end of the cycle. Too wet to put in the dryer. It is also making what I would call a squealing/high pitched mouse sound during spin cycle. Would this be the fix for that issue?
For model number MAV6458AWW
Hi Danielle, thank you for your question. The issue is probably related to the transmission pulley, part number PS2003651. It includes the pulley that rotates to spin the basket and the thrust bearing that fits between the pulley and the transmission shaft. If this does not help you need to check the drain pump, part number PS11741803. It removes water from the washer during the drain portion of the cycle. We hope this information helps!
This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt encounter wear and tear.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing help...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
