![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Front Top Lock
Fits your 1105804802!
$16.83
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your 1105804802!
PartSelect Number
PS11738705
Manufacturer Part Number
WP18776
Manufactured by
Whirlpool
Product Description
Front Top Lock Specifications
This part is used to secure the top panel to the cabinet. Sold individually.
![How Buying OEM Parts Can Save You Time and Money How Buying OEM Parts Can Save You Time and Money](https://img.youtube.com/vi/d6AvOkulk_g/maxresdefault.jpg)
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Dryer Front Top Lock
![Replacing your Kenmore Dryer Front Top Lock Replacing your Kenmore Dryer Front Top Lock](https://img.youtube.com/vi/R_f-SphmiXM/maxresdefault.jpg)
Troubleshooting
This part works with the following products:
Dryer, Washer, Washer Dryer Combo.
This part works with the following products:
Kenmore, Whirlpool, KitchenAid, Roper.
Part# WP18776 replaces these:
AP6005653, 18776, 230555, 353145, 502682, 50268200, 688904, 690363
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 5 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
broken clip on top panel hold down
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Other Parts Used:
-
Mark from Huntington Station, NY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
15 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor failure
Used this resource and others' advice -thank you . Make sure to disconnect power first. I had replaced the rollers and tensioner a week earlier due to squeaking, but mine was the rare one where squeaking meant motor failure, so I had to place another parts order. The dryer was 19 years old, and my blower wheel did not simply 'unscrew with reverse threads'. During removal the blower wheel's plastic deformed, so had to do like someone else did and cut the rear shaft with a reciprocating saw. Just be careful not to damage the bulkhead's built-in bracket that anchors the rear of the motor. I think it was a 13/16" wrench that fit the blower wheel and I forget the size for the pulley nut on the front of the motor, but I suggest a deep socket since it held well. My best advice when dealing with a motor replacement is to ensure the blower wheel wheel will separate successfully from the motor before placing your parts order should it be a stubborn removal. Good luck.
Other Parts Used:
-
James from COTTONWOOD, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set, Wrench set
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Top Panel is Loose
1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
Other Parts Used:
-
MONTE from CHESAPEAKE, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not turn on
Found the switch part on the floor and after I figured out where it came from it was minutes before it took to find the web site and order the part, I then watched the installation video which helped with a few pointers and days later it was installed and fixed for 10 dollars with shipping,AMAZING!!!
Other Parts Used:
-
Larry from Bethpage, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Dryer belt
Speaking on my husbands' behalf, the belt was easy to replace with the helpful instructions provided. I am also enjoying the new lint filter that we also purchased. He is so glad he found your website and was able to replace the dryers parts with no problem. The delivery was fast which really helped me out, since I wash and dry clothes almost daily. Thank-you for having just what we needed to get our dryer running again!
Other Parts Used:
-
William D. from LUVERNE, AL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jay
February 27, 2019
What is the part number for the retaining clips that fasten/ hold the lower front panel on my model dryer?
For model number GEQ9800PW1
Hello Jay, thank you for your question. The top panel clips are Part Number: PS11741425 and the bottom panel clip is Part Number: PS11740620. Please enter the part number into the site for current price and availability. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Deborah Wilson
April 3, 2019
I need new clips to hold the top panel of washer to base.
For model number LSQ9659PW4
Hello Deborah, thank you for inquiring. The Cabinet Retaining Clips for your model are part PS11743311. They are sold individually.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738705
Manufacturer Part Number: WP18776
Manufacturer Part Number: WP18776
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)