MLE19PDAYW Maytag Washer Dryer Combo - Instructions

I followed the other instructions provided by your toher users. Basically I reomved the 4 face screws secruing the front pannel assembley and the door hinges as described with a philips head screw driver. Removal of the door was easily accomplished once you played witht he hinges to slide them upward slightly to clear the lips. The soap dispenser was then loosened by removing the 4 corner screws. Take care not to completely remove the soap dish. It simply needs to be moved aside with the flexible hoses still attached. This is accomplished once the top lid is hinged upward out of the way. The face panel can then be removed and set asside ater removing the screws holding it in place. Remove the damaged boot with the anterior face (door side)first. It simply gets pulled away from the sealing flanges. With the top lid removed you should have direct visualization and access to the retaining cable and the spring tensioner. I found that neither of the previously described methods of taking the tension with pliers or having an assistant were particularly helpful. Under the soap dispenser you will notice a hole in the top lip of the side frame. I attached a piece of rope to this hole using a small snap link. The other end of the rope had an "s" link set into the middle of the rope and the other end hooked over the spring hook. Now puliing back on the loose end of the rope back towards the attachment point creates a mechanical advantage easing the spring open and then using pliers you can easily remove the retaining cable. Ease off the spring and then set aside. The posterior portion of the door boot can now be removed and the old piece discarded. Take care to disconnect the drain plug at the bottom first. Replacing the boot was fairly straighforward. I attached the posterio portion first taking care to align the indentions were appropriate. Once is was attached and aligned, use the rope assembly once again to draw tension on the spring in a controlled fashion. Hold the other end of the cable with some needle nose pliers and slip over the spring hook once enough tension is applied. This method only took me one try and the mechanical advantage created was very effective. I then turned my attention to the anterior portion of the boot and pushed it into the flanges. I also found the the required pressure was a bit stiff and your fingers will get tired quickly. Use a smooth stick or a spatula particularly underneath the door latch assembly since space is tight and you will not be able to get your fingers underneath it. Put the face palte back in place and reattach the screws. Put the soap dispenser assembly back in place and hinge the lip back into place. Reattach the screws for the soap dispenser and lid. Reattach the door and test everything for any leaks. It was not very diificult at all and it took roughly 30-45 minutes. Read all of the other stories as well to help get an overal flavor for the job beforehand.

From previous experience I suspected the thermal fuse. Turned off the power and removed the front of the dryer by removing the two philips head screws in the door hinge and the two screws on the opposite side of the opening. The front came off easily since all that holds it in place besides the 4 screws are two spring clips. The thermal fuse is located on the side of the chamber enclosing the heating element. I removed the wires connected to the thermal fuse and temporarily joined them together with a spade type connector in order to determine if the thermal fuse was the problem. Turned the power back on and tried the dryer......it ran normally. Turned the power back off and removed the thermal fuse by taking out th two screws with a 1/4" nutdriver.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.

we replaced the baffle by removing the broken baffle. There were two screws holding it in place. Door and front panel of dryer had to be removed to accomplish this task. Quite an easy repair/replacement. Thank you for all your help PartSelect.com.

We took off the fornt and back of the machine and pulled out the outer tub...then pulled the rear and the front bearings...and the sleeve between...and the support arm...We had only thought we would replace the bearings, but there is a seal in the hub of the support arm that often goes wrong and causes the bearing problem...That appeared to be the case in this fix...so we are glad we chose to replace the arm too. Then we reassembled in reverse order and voila! The machine is as quiet as can be!

I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.

Not much to add to others' descriptions of the repair except for two things- one, the procedure for removing the front shroud on a stackable unit is somewhat different than what is described in the seal kit directions. The door switch assembly gets in the way; though the whole repair can be done by one person, it would be better (and safer) to have a second person helping at least during this part. The whole shroud is unwieldy, with two drain hoses attached, along with two dispenser hoses, the door switch/light, and the side & bottom mounting brackets, and it has to be eased out one step at a time. During the last part of this you will have to lift up the front of the dryer at the same time.

Second, our particular washer has a 90xxxx serial number. The bearings are Chinese-sourced, not the good NSK bearings. Though the listed bearing numbers are the same... the rear bearing is held in by a retainer that is permanently fixed into the outer tub. There is no easy way to drive the bearing forward, either, as the retainer covers nearly all the bearing outer shell. The chances are very high that the outer tub would be damaged beyond repair if the retainer or bearing was removed. Fortunately in this washer, the back bearing was still in reasonable shape and had some grease left; I was able to pop out the grease seal and re-pack it with wheel bearing grease. The front bearing & seal are replaced as others have described. The front bearing takes a majority of the load, so others may have similar wear.

This washer was only 3 1/2 years old; we bought six Maytag appliances at the same time, and four of the six have had major repair problems (two were cheaper to replace than repair). That, and the $678 replacement cost of the outer tub, explains why the Maytag repairman is so lonely...

I followed the directions that came with the conversion kit; which I ordered from PartSelect. Your website was the only place that could help me. Our new dryer is actually a Samsung. The people at Best Buy were no help. I called the Samsung headquarters and a "real" person there told me I could order from them or use a Whirlpool kit because they are the same. You guys were faster in getting me one, so I went with you. My wife was happy. I would recommend you to others.

Turned off circuit breaker. Removed two screws at base of front panel with stubby Phillips-head screwdriver. Swung panel up about 30-degrees, and removed panel, disconnecting red and yellow wire to door switch. Removed four sheet metal screws and took off large drum support bracket. Checked drum support rollers and shafts. They were fine. Reset circuit breaker and turned on dryer. Rattling noise still present.
Removed six small screws holding blower fan assembly. Shaft receiver on squirrel cage fan was worn completely round (it should fit onto a half-round shaft). Ordered new blower fan from PartSelect.com. Replaced tonight, and it works beautifully. This dryer is 29-years old. All it's ever needed in the 10-years I've owned it is a belt replacement and this repair. Long live the 1970s Maytags, and good parts suppliers like this one.

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

Unplug the dryer and remove the front panel (two screws at bottom of the panel), being careful of the door switch wires attached to the front panel. Using an ohm meter, I checked the ignitor for continuity and found it was open (should be 50-100 ohms). Make sure to check the solenoids on the gas valve. When the igniter goes bad, it will usually burn out the valve 1 solenoid boost coil (the one with 3 terminals), which was the case with my dryer. The solenoid coils are held in by a bracket with two screws (series 01 dryer) and are easy to remove and replace. Be careful replacing the igniter as the heating element is VERY fragile. Take the time to vacuum out all of the accumulated lint and dust inside the dryer while the front panel is removed, including the lint trap and duct. New igniter and boost/hold solenoid fixed the problem.

Removed the screws and took the door off then took the front panel off and popped up the top. Then pulled the drum out. Took snap ring pliers and removed rollers and replaced with new rollers then vacuumed all lint from machine and reversed operation to put everything back together. Operation was a total success!

Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old to new pump. Install new pump in reverse order as above.

Note: You may want to consider replacing the 2 Drum Support rollers at this time (while your in there)

1. UNPLUG YOUR DRYER FIRST.

2. Using a phillips head screw driver - Remove 2 screws that secure the dryer door hinges to the frame, Lift door very slightly to unhook hinges and pull out door with hinges attached as straight as possible, set aside. Remove the 2 plastic tabs from the opposing side of the door hinge also secured by screws.

3. Remove the front panel (panel is shaped like a football goal post) by tilting out the top ends of the front panel toward you, then lift up to remove panel from the bottom metal retaining tabs.

4. Remove the 2 hexhead screws from the 2 retaining clips (security hooks) that secure the top
of the dryer closed.

5. Systematically remove the hexhead screws from the rest of the front of "shroud" (it holds (suspends) the drum in place between the front and back of the dryer).

*** I didn't disconnect any wires, I carefully swung out each piece that had wires attached, propped up those parts vertically ensuring no strain on the attached wires. Others may want to disconnect wires to avoid breaking or damaging them.

6. Vacuum out any dust/lint that may be present.

7. Draw a quick diagram of how the underside of the belt is threaded on the idler pulley and motor pully first. Release the tension of the belt from the underside of the drum. The easiest way is to push the idler pulley arm away from the belt and slide off the belt from the idler pulley and motor pulley. Slide the drum out.

8. Remove the hexhead screw from the bottom of the idler arm. Disconnect from retaining spring.

9. You may only need to replace just the Idler Pulley Wheel. I recommend replacing as a "unit" the Idler Pulley Wheel, Idler Arm, Ring-E and Idler Shaft Washer(s) - then you can just swap out the old one for the new one.

10. Reassemble

(When reassembling the belt - place around drum first and slide drum in place. Now from the underside-place (drape) belt around the motor pulley (it will be very loose) Now push the idler pulley arm toward the motor pulley, engage the left side of the belt around the idler pulley and slowly allow idler pulley to increase its tension on the belt) You can test manually by rotating the drum by hand to ensure proper movement.)

I removed the front of the dryer by removing the two screws on the bottom of the front panel, disconnected the door switch wires. I removed the connectors from the coils on the gas valve, the heat sensor and the igniter. Loosened the gas line at the valve. I removed the screw holding the gas valve and burner assembly and removed the assembly from the dryer. Remover the screw holding the burner to the valve, and removed the igniter. Replaced the burned and reconnected what I had removed. The reason the burner didn't light was due to the gas deflectors being burned off of the burner, If the igniter, sensor, and coils check out OK , check the front of the burned to besure it is deflecting gas to the igniter

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.