MDE6700AYW Maytag Dryer - Instructions

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

Test thermal fuse for resistance. If has 0 resistance you have a bad fuse. Also check voltage going to wall outlet. Must use at least 600 volt tester. Motor will run on 110 volts, but will not activate heating element. Heating element must have 240 volts to operate. Always make sure you turn off power when working on electrical problems. Be safe and good luck.

The lemon that I bought has forced me to open it up at least once a year. Anyone with a #2 phillips screwdriver and a good memory can take the challenge. Youtube has few videos on the same model. Best regards, Jim

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

This was a simple repair. Removed the small access panel where the vent pipe comes through, the roller is right there. Unscrewed the support roller bolt, looking for all the pieces that had broken and fallen inside the housing of the dryer. Using the washers and nut from the old one, put the new roller in place, be aware that you have to lift the drum a little bit to get this new roller in. It could take two people depending on your strength. Tightened down the roller, spin the drum by hand to make sure it was ok, then put the access panel back on and fired it up for a test run.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

After reading other posts, I learned that "tO" meant that the thermistor was open. Also, I read that this part would bench test with a multimeter correctly but could still malfunction in the dryer. FIRST UNPLUG DRYER. After checking all of the exhaust ducting including inside the dryer for any blockages that could result in an overheating problem I decided to order a new thermistor. To replace thermistor: First, there are two screws at the rear top that you remove and the top tilts up and comes off. There are four screws on the top front that removes the front control panel. Next remove the screws at the top of the dryer, two screws in recesses behind the door and tilt front forward while unplugging the door switch. Lift and remove front with door attached. Remove screws from exhaust duct and slide down and out. Thoroughly clean inside of duct and fan blades. Clean out any other lint build up. Locate thermistor to the right of duct, unplug and remove two screws. Replace with new part and reassemble while not forgetting to plug the door switch back in. At the rear of dryer, remove screws around exhaust duct and remove. Dryer will have to be slid away from wall about three feet to remove duct from inside dryer. Clean thoroughly and check/clean and check for blockages in ducting from dryer to outdoors. Re assemble making sure rear duct engages the front ducting properly.Plug dryer back in and enjoy.

You know! I forgot exactly where it was i got the info to fix the problem but, "Parts select" was mentioned. Once I had an idea as to what to do I then, wasted time around town looking for the parts with no results. I then did what I should have at first an ordered the parts from Parts select. got them in the mail, lightning quick! I think I may have found the info here as well,not sure. (this site is awesome None the less) but the info led me to the Thermostat, I then jumped it as indicated and wham!! it ran. Order both the thermostat and thermistor. only problem I ran into was, removing the front display panel. broke some of the retaining clips off in the process. all in all, it was an easy fix that saved me a bunch of dough. greatfull to parts select for a speedy deliverie and to the website that made it possible. think it may have been here at the free repair help, section. awesome and highly recommended thanks!!!