LSE7804ADE Maytag Washer Dryer Combo - Instructions

All Instructions for the LSE7804ADE
91 - 105 of 1108

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
filled with water, would not wash nor spin
10 of 12 people found this instruction helpful.
  • ELINOR A from MEDINA, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
After I replaced the timer, the washer still would not wash or spin. So my son replaced the lid check switch. It was hard to remove the screw, but he finally managed to remove it and easily replaced the switch. The washer works perfectly. We kept the timer installed (also easy to do by removing the old and replacing it with the new by ju st unplugging wires and I think one screw) because the old one had not worked properly for a few years when I had a similar problem which resolved, except it would only work in main cycle with soaking which was sufficient for me. This large capacity washer is in good shape and I hope will last at least another 5 - 10 years. ).
Was this helpful?
Thank you for voting!
no water drain
20 of 26 people found this instruction helpful.
  • Franz from Lakeland, FL
  • Easy
  • Less than 15 mins
removed old pully, put new one on with hex driver, removed belts, put new belts on and finished.
Was this helpful?
Thank you for voting!
Dryer would not turn start
10 of 13 people found this instruction helpful.
  • John from Midway, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I troubleshot the repair using the repair help section from Parts Select. It made finding the problem a snap. I then removed the four wires and two screws that held the heating element in place. Removed two screws that held thermal fuse in place and replaced. By accomplishing the repair myself I saved well over a hundred dollars.
Was this helpful?
Thank you for voting!
Standing water in washer tub
9 of 10 people found this instruction helpful.
  • James from Baton Rouge, LA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).
Was this helpful?
Thank you for voting!
Washer did not drain.
9 of 10 people found this instruction helpful.
  • Basil from St. Charles, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Chec ked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.
Was this helpful?
Thank you for voting!
tub leaked
8 of 8 people found this instruction helpful.
  • Fritz from Redway, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
followed instructions elsewhere here. Procedure went flawlessly
To undo the nut I used a 1 1/2 " long x 5/16 bolt to hammer on.

STILL LEAKS. Needed PS2347235 =Tub Bearing Kit . Going back in...
THe remainder concerns the bearing procedure:
The 3 bolts holding the outer tub to the legs have rectangular washers. Those are not totally flat, and are marked for outside, top ... so pay attention. It might make a difference.
Outer tub came off the rubber bushing. Took some pulling the bushing off the shaft, and removing the sleeve bearing was a challenge at first, it would not move on the transmission shaft. Soaked with wd40 overnight. Drove it off with cold chisel (driving upward). For re-attaching the 3 tub bolts I used a ratchet tiedown strap to pull the 3 legs together to get enough thread to start, what with all those washers and things.
Ran spin cycle dry for 3 minutes as per instructions before filling with water. Success.
Was this helpful?
Thank you for voting!
Motor needed replacing (even though it was only 8 years old!)
9 of 11 people found this instruction helpful.
  • ian from new york, NY
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
In addition to the other helpful suggestions:

The key to replacing the motor is to remove the motor while it is still clipped in to the bracket (after removing the blower assembly, of course.) Don't remove the tumbler and belt thinking it will give you clear access to the rear clip, because it won't.

Removing the bra cket is not complicated. There are two screws that are fairly easy to access and keep the bracket in place (refer to parts diagram for location); when the screws are removed, out comes the motor assembly (after disconnecting the wires, of course.) This is the only way to get access to the two clips that hold the motor to the bracket.

As for those pesky clips, I was able to use a flat screwdriver in one hand and vice grips in the other to pry off the clips. After a few tries, working on one end of the clip, I was able to apply quite a lot of downward pressure without braking the end of the clip. If anyone has another suggestion....

Putting the clips back on was much easier. First, remount the motor to the bracket, making sure to rotate the motor to the 2 o'clock position so you can re-attach the ground wire (or else you'll have to unclip the motor again, like I did!) Then re-attach the clip on one side. With the clip aligned properly, bear down with a flat screw driver on the other end of the clip. A swift knock with a hammer on the top of the screwdriver will easily re-attach the clip. Repeat with the second clip.

If you proceed carefully and patiently, this job can be accomplished without specialized tools or expertise.
Was this helpful?
Thank you for voting!
washer fills with water wont start
9 of 11 people found this instruction helpful.
  • JOHN from ERWIN, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
checked lid switch ,plunger stuck in the in position 1 amp fuse blown took switch apart it was full of green copper corrosion stopping plunger from moving correctly. replaced switch and fuse and wow washer works
Was this helpful?
Thank you for voting!
Dryer did not turn off in auto-dry mode
11 of 17 people found this instruction helpful.
  • W. Dale from Newton, KS
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Unplugged the dryer (electric), removed two screws at bottom of front panel and removed front panel. Pulled electrical clips from sensor lugs near center.front of drum exterior. Located sensor inside front of drum interior, removed screw at each end. Removed old sensor, placed new sensor in position, attached with screws. Installed ele ctrical clips on lugs, closed front panel and secured with two screws. Plugged in the dryer and it worked!
Was this helpful?
Thank you for voting!
Washer would fill but not continue the cycle
9 of 11 people found this instruction helpful.
  • Paul from Cedar Falls, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I looked at the common problems in the owners manual and one item was the lid was not closed or the lid switch was bad. I took off the control panel and there was a schematic inside. This showed 2 lid switches. When trying to see if one switch was closed as it should be, touching the multimeter to the contacts was enough to get the was her going. .
Was this helpful?
Thank you for voting!
Noise in dryer
8 of 8 people found this instruction helpful.
  • Joseph from Hampton bays, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
How to disassemble the dryer has been covered in past repair stories. I will add a make shift repair that will get you up and running until you get your replacement blower wheel. We repair gas dryers for a living and this repair works and some machines are still running for two years. Remove the blower wheel. Cut a piece of plumber strap of similar sized metal to about 3/16" x 1/2". Hold it with vise grips and then heat it with a torch. When it is hot melt it into the hole in the blower wheel. This will give you a flat spot in the shaft hole that will keep the blower from spinning on the motor shaft. Some trial and error fitting is involved. If you do it carefully the blower wheel will fit very nicely and will not vibrate or make noise.
Was this helpful?
Thank you for voting!
Floor floded when washer started.
9 of 12 people found this instruction helpful.
  • Keith from Big Sur, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Thirty year old Maytag washer. Remove two screws at bottom of front panel with Philips screw driver. Hinge panel up to disconnect front panel from top of machine. Tilt washer back against wall to gain access to pulley at underside of washer. Then remove Philips head screw from bottom of center shaft. Remove bevel washer with screw. Remove stop block from end of center shaft and wind the pulley off center shaft. Clean center shaft of any debris and lightly coat with grease. Install belt on new pulley and motor, wind new pulley on center shaft. Replace stop block, washer, screw, and front cover.
Was this helpful?
Thank you for voting!
Water leaking into basin when washing machine not in use
9 of 12 people found this instruction helpful.
  • Tate from Carrollton, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
Turn off water. Disconnect hoses from washer. Remove drain hose from plumbing drain in wall. Catch water from all three hoses in plastic tub. Remove two 5/15 machinve screws holding inlet valve cover/mount plate. Remove fill hose by compressing hose clamp ends with pliers. Remove electrical connections. Reverse to install. Easy as p ie!
Was this helpful?
Thank you for voting!
washer was leaking when water level got about 4 inches in tub
7 of 7 people found this instruction helpful.
  • Brian from Bush, LA
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
It was fairly easy, start out by using a screwdriver and push down and out on the front cover and remove it. Take out the 2 small bolts that hold the top cover down to the sides and lift the top cover up and lean it back out of your way. On the bottom side of the agitator there is a small bolt that holds it down, loosen that bolt and pull the agitator out. The hardest part of the entire jod was to use a small chisel and hammer to take off the nut that holds the assembly down.Remember it has reverse threads,you have to use a chisel to back it off and use some WD40 to help remove the calsium build up that is around it. Once you get that large nut off, there is a set screw on the side of the assembly that you have to loosen up before you can take it off, it's a "star driver" head and not a allen wrench set screw.Just take your time and look at your new part and compare it with the old one and take your time and remember how you take the old part off,and you will not have any problem putting the new one on. This was the first time I ever worked on a washing machine, and by checking out the parts first and comparing everything,even someone that might not have much mechanical skills can change this out. My washer works fine and not a drop of water leaks anymore.One thing I did learn, if you change this part out and put it back together and try it out and it makes a funny sound and you smell something like its burning, you might did what I did. I thought I had it to tight, but I put the large nut on before I put the tub back on!!! The agitator was holding the tub down, but it could not spin in spin cycle.... Good luck with you repairs, you can do it.
Was this helpful?
Thank you for voting!
My dryer - which is about 20 years old - was starting to make some rubbing/scraping sounds from the drum area.
7 of 7 people found this instruction helpful.
  • Richard from Loretto, MN
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
This was pretty much as easy as most other folks had described on this site.
1. Removed the two screws at the front bottom that are holding on the fromt panel, and then lift up and remove the panel.
2. Disconnect the door-open-safety-switch, remembering which color of wire goes on which connection.
3. Remove the four s crews (two on each side) on the front bracket that supports the drum and tthat contains the front glides.
4. Remove support bracket and lint trap, letting the drum rest gently on the stuff underneath.
5. Remove the screws holding the lint trap to the support bracket. (My model had five screws.) Remove lint trap from support bracket.
6. Drill out the two pop rivets on each of the two glides, noting the orientation of the teflon pad and mounting strip.
7. Secure - and here is where I had a little problem - new glides in place with pop rivets. (I hadn't use a rivet gun in a while, so I messed up the first pop rivet and had to go to the hardware store to get a replacement. I didn't hold the pop rivet in all the way while I was accuating the gun!)
8. Reverse the process for assembly, and you are all done.

It's simple.
Was this helpful?
Thank you for voting!
All Instructions for the LSE7804ADE
91 - 105 of 1108