LSE7804ADE Maytag Washer Dryer Combo - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum Support Roller Kit – Part Number: 12001541
$33.28
In Stock
Drum Support Roller Kit
★★★★★
★★★★★
(74)
Part #12001541
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once.
Tumbler and Motor Belt – Part Number: WPY312959
$37.35
In Stock
Tumbler and Motor Belt
★★★★★
★★★★★
(63)
Part #WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair. During the repair, make sure the belt doesn't fall into the groove in the drum, which will cause it to be too loose. You should be able to access the belt and replace it by removing the front panel and bulkhead.
Roller Shaft – Part Number: WP6-3129480
No Longer Available
Roller Shaft
★★★★★
★★★★★
(1)
Part #WP6-3129480
This roller shaft is the axle for the drum roller, also known as drum roller axle.
Front Glide Kit – Part Number: 306508
$19.14
In Stock
Front Glide Kit
★★★★★
★★★★★
(16)
Part #306508
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
Blower Wheel with Clamp – Part Number: Y303836
$32.26
On Order
Blower Wheel with Clamp
★★★★★
★★★★★
(59)
Part #Y303836
This blower wheel comes with a metallic hub clamp to hold it firmly in place.
Belt Kit – Part Number: 12112425
$50.55
In Stock
Belt Kit
★★★★★
★★★★★
(45)
Part #12112425
This kit includes both the drive belt and the pump belt which are both "V" shaped.
Lint Filter – Part Number: WP33001003
$42.36
In Stock
Lint Filter
★★★★★
★★★★★
(60)
Part #WP33001003
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
Dryer Retaining Ring – Part Number: WP9703438
$12.00
In Stock
Dryer Retaining Ring
★★★★★
★★★★★
(3)
Part #WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
Drum Roller Shaft Washer – Part Number: WP312535
$18.41
In Stock
Drum Roller Shaft Washer
Part #WP312535
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
Mounting Stem/Tub Seal Kit – Part Number: 6-2095720
No Longer Available
Mounting Stem/Tub Seal Kit
★★★★★
★★★★★
(13)
Part #6-2095720
This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
Idler Pulley Wheel – Part Number: WP6-3037050
$25.19
In Stock
Idler Pulley Wheel
★★★★★
★★★★★
(4)
Part #WP6-3037050
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
Dryer Door Catch Kit – Part Number: LA-1003
$35.75
In Stock
Dryer Door Catch Kit
★★★★★
★★★★★
(13)
Part #LA-1003
This kit comes in two pieces: the catch and the clip.

Manuals & Care Guides for LSE7804ADE

Click to download

Questions And Answers for LSE7804ADE

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred - For model number LSE7804ADE
December 21, 2019
How to operate the washer ?
Chris Boyle Profile
Hello Fred and thanks for writing. For your convenience, we have attached the link to your manual with repair instruction. We hope this helps. Good luck with your repair https://www.manualslib.com/manual/100403/Maytag-Stacked-Laundry.html
Was this helpful?
Thank you for voting!
Fred - For model number LSE7804ADE
December 22, 2019
I do not need parts,but how do i operate the washer,(where does the soap goes, and how much? How much fabric softener and where is added.? thanks
Chris Boyle Profile
Hello Fred and thank you for writing. For your convenience, we have attached the link to your manual with repair instruction. We hope this helps. Good luck with your repair. https://www.manualslib.com/manual/100403/Maytag-Stacked-Laundry.html
Was this helpful?
Thank you for voting!
Thomasine - For model number LSE7804ADE
March 26, 2020
I have 1997 Maytag stackable washer/ dryer. The washer just went out. I want to get another but i cannot find cu. Sq capacity.
Chris Boyle Profile
Hello Thomasine, Thank you for the question. We believe this question is best addressed by the manufacturer. We are a parts distributor. We do not manufacture any units, or have access to dimensions and year of manufacture for the models. We hope this helps.
Was this helpful?
Thank you for voting!
Kenneth - For model number LSE7804ADE
December 15, 2022
When the washer goes into the spin cycle even with a smaller load there is a loud knocking noise. Can this be serious and is it possibleto repair
Chris Boyle Profile
Hello Kenneth, thank you for reaching out. You will need to check the following parts: the drive belt, part number PS11757542, the belt kit, part number PS2005284, the tub bearing kit, part number PS2347235, the rear bearing, part number PS11739437, and the transmission drive pulley, part number PS11743025. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
$50.55
In Stock
Belt Kit
$97.91
In Stock
Tub Bearing Kit
$27.69
In Stock
Rear Bearing
$182.52
Special Order
Transmission Drive Pulley
$37.35
In Stock
Tumbler and Motor Belt
Was this helpful?
Thank you for voting!
David - For model number LSE7804ADE
May 11, 2024
Does the dryer have a thermal fuse that can be replaced?
Chris Boyle Profile
Hi David, thank you for getting in touch. The dryer of your model comes with two thermal fuses that can be replaced: part number PS11740687, and PS11740678. If you need help placing an order, customer service is open 7 days a week!
$45.09
In Stock
Thermal Fuse (Limit: 183)
$67.20
In Stock
Thermal Fuse
Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the LSE7804ADE

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum would not drain and there was a banging noise when the drum spun
600 of 658 people found this instruction helpful.
  • Charles from Whitman, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
574 of 583 people found this instruction helpful.
  • Stephen from Lafayette, IN
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Was this helpful?
Thank you for voting!
electric dryer was rumbling - wheel or belt?
602 of 711 people found this instruction helpful.
  • Raymond from West Bend, WI
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through . Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
Was this helpful?
Thank you for voting!