JS42PPDUDB15 Jenn-Air Refrigerator - Instructions

Removed old filter and installed new filter.

Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.

Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/deliv ... Read more ery was fast. No need to have spare on hand.

I did some research on the website and found out that there is a test with the sensor lights. When I looked at mine, they were not turning on or blinking when the door was openned.

The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the ... Read more circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.

A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.

I saved about $200 in service fees!!

Go first to Kitchenaid web site and download their consumer services Technical diagnostics on the ice maker. Very well written and clear to follow. Instructions step you through interpretation of blinking code lights which is key to finding the real problem and leads you to repair the correct failed part. My diagnosis said to replace both ... Read more emitter and receiver. I replaced the emitter first and tried it and solved the problem I didn't need to buy the receiver but I have a spare part now. Do the diagnosis and save yourself some money. PartSelect got the parts to me quickly and saved me money compared to our local parts supply companies.

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old moto ... Read more r unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

I had a son put in the new light bulbs. Rather simple

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

The repair went just as simple as the video on the web site. Parts came really fast. replaced in less than 15 minutes. i thought the icemaker unit was the bad part but after gettin info from this site it told me waht to check first and i found that the emitter boards were bad. Thanks for saving me the money on buying the wrong parts. also ... Read more bought parts the folowing week to repair my wifes kitchenaid mixer.

unscrerwed the broke part and screwed in the new one---5 minutes

Removed old ejector arm and installed new part.

Just needed to replace the water filter

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by takin ... Read more g out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I had watched several video's on installing the plugs in the Kitchenaid model that I had, but when it came down to the install the figuration was a little different. I did figure it out and the rest was a piece of cake. Remember to shut the power off!

Followed the instruction video.