FGID2466QF4A Frigidaire Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Parts Used:
-
david from hull, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper Spray Arm kept falling off.
The new arm came preassembled. I unscrewed the old arm base with my hand and screwed the new arm in place. The whole process took less than a minute. The new part was not made the same way. It was better than the original. Must have been a problem from the manufacturer. WORKS GREAT!!!
Parts Used:
-
Martin from Bonaire, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spray arm broke
-
phil from lindenhurst, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper spray arm kept falling off
This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.
Parts Used:
-
Todd from Brandon, SD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing a wheel on dish rack
-
Pam from Cherokee, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing roller made it difficult to move rack.
-
Racquel from Lake Charles, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper spray arm separated from arm retaining nut.
VERY simple repair - just unscrew the retaining nut by hand and hand screw on the new spray arm and nut assembly. A 30 second fix!
Parts Used:
-
Michael from Cumming, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper spray arm kept blowing off
Easiest repair ever. The spray arm itself usually really is not the problem, it usually is the clip or gasket that holds the spray arm on. It wears out. This part is perfect for it supplies a new spray arm, nut and gasket/clip. I think it wears out due to a build up on the arm that puts too much pressure on the clip/gasket. Remember when taking the nut off, if you are standing above the unit with your arm inside, you turn the nut clockwise while looking down. Good luck.
Parts Used:
-
Perry from Waynesboro, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak
-
MICHAEL from FT LAUDERDALE, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
A piece of the upper rack began to rust out
Used the screwdriver to pry the upper rack left side tine up and out. Slipped the new one into place and pressed hard to seat the tine. this process took all of about 20 seconds to do.
Parts Used:
-
Carl from EAST ISLIP, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaked spot free fluid
-
Tim from MARINE ST CRX, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken LOWER SPRAY ARM
-
Donald from STOUGHTON, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spray arm fell off during cycle
Unscrew old one and put new one in. Only issue we had was the new nut that screws the arm into place did not fit our machine. We had to take the old one off and use it instead.
Parts Used:
-
Dana from PATTON, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spray arm would detach and dishes didn’t get clean
-
Mary from FIRTH, NE
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spray arm broke free from mount
unscrewed and remove the original mount....this is only hand tight. install new spray arm, hand tight only, threads are plastic and could strip if over tightened.
Parts Used:
-
Eric from Linthicum Heights, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!