This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
The drain pump ejects the water from the dishwasher.
$137.48
In Stock
Questions And Answers for FGID2466QF4A
Ask our experts a question about this model and we'll get back to you as soon as possible!
14 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
February 24, 2020
Doesn't turn on. I have power to dishwasher. Door latch switch works. No display at all. Most likely problem? Control board? Touch display? Is there a fuse?
For model number FGID2466QF4A
Hello Jim,
Thank you for your question. Our sources suggest that its likely a faulty control board under part PS11758074 for your model to fix the power issues for the dishwasher. We hope this helps.
I am looking for a sound proofing/insulating fabric that sits on top of the unit , before the countertop is mounted on top of it. Cannot seem to find it on your site!Thanks!
For model number FGID2466QF4A
Hi Daniela,
Thank you for your question. There is insulation that goes around the dishwasher. The part number for it is PS11703938. We hope this helps. Thank you and have a great day.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Diep
December 6, 2023
Can you give me the dimensions of my dishwasher? I can find it on the internet?
Thanks
For model number FGID2466QF4A
Hi Diep, thank you for your question! The dimensions of your model are:
Minimum Height: 33 1/2 inches.
Maximum Height: 35 inches.
Width: 24 inches.
Depth: 25 inches.
We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
William
March 31, 2024
The plastic on the control panel where the start button is cracked all the way through . Button popped off .
For model number FGID2466QF4A
Hello William, thank you for getting in touch. According to our research, the start button does not come separately, and it comes with the control panel assembly, part number PS9865008. You may need to replace it to solve the problem. We hope that helps!
My washer does not fill with water & shows a code of “Uo”.
What part do I need?
For model number FGID2466QF4A
Hi Berton, Thank you for reaching out. The UO error code indicates that the main control board has detected an issue with the vent assembly's vent plunger. We suggest checking the wire harness to the Vent and the vent is clear of any obstructions. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
