FDE747RES0 Frigidaire Dryer - Instructions

Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws ... Read more that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

Repair to replace motor and blower kit. Disconnected Power Source and turned off breaker. Removed top and front with screwdriver. Removed back plate with screwdriver. Disengaged belt. Removed plastic piece in front top with phillip screwdriver. Removed Drum. Disconected thermostat from blower. Unplugged motor connections. Removed ... Read more screws holding in blower unit. Removed blower unit and motor as a unit. Removed pully unit (2 Screws). Took off blower unit security nut to be used on new unit. Took old seal out of pully unit. (New Motor has one installed on it). Put pully unit back in. Put in new motor and blower unit. Screwed them in place. Reconnected thermostat. (2 screws).
Connected electrical plugs to motor. Put drum in and plastic piece in front top of dryer. Hooked belt back up from rear. Replaced rear door. (2 screws). Reconnected ground wire on back top of dryer. Put on front making sure all wires to Timer are connected(they can pull off when taking drum out). Close front. Polug dryer in. Reset dryer in place. Turn on Breaker. Done.

I contacted a company to come out and diagnose the problem. They informed me that the thermal limiter is bad and needed to be replaced for $15 for the part and $85 labor. I found the part on this site for about $10, and did the repair myself. The dryer was mostly dismantled so I pulled the drum back, and replaced the part. The tricky ... Read more part was the pulley system was, so make sure you see it before hand or find a diagram online. Once that was figured out, I set the drum back up, greased and tightened the pulley, reattached the front of the washer with connections, and closed the lid.

Tried to follow the directions of others but ran into a problem with getting the top panel off. This is how I did it.
1 Disconnect power and dryer vent tube. Move away from wall.
2 Remove slotted access panel in back of dryer and take belt off motor and idler pulley. Leave on drum.
3 Unscrew the screws on the back of the t ... Read more op panel brackets( mine are silver) where they screw into the back panel and pull up and to the back to get the top panel off. Someone else said to slide a putty knife in the front to release the top but my machine has no spring clips.
4 With the cover off you can see the two heat sensors and I tested them with a multi meter they registered 0 which meant they were OK.
5 Remove the screws that hold the control board on and the plugs that are wired into it making sure that you draw a diagram to remember the wiring. There was a zip tie that I cut to be able to feed the plugs through the hole in the front panel that the wiring must go when the front panel drops down.
6 Remove the screws on the top of the front panel and the screws on the inside of the side panel that hold the front panel secure.
7 A lot goes on on step 7 because the front panel which is hinged drops from the top down to the floor. Diagram and remove all wires there are two green ground wires on the side, Three wires on the door lock, two wires for the light and wires for a moisture sensor. When disconnected feed the control panel plugs and other wires through the hole in the front panel and lift up and out on the front panel it will pop out. Lower it to the floor and let it rest there.
8 Now you can get the drum out of the way by pulling up then out the front where the front panel is now on the floor. Leave the belt on it.
9 Diagram the wiring on the heating element there are connections for the element and the sensor. They gave me a new sensor screwed onto the new heating element. Then unscrew it from the back panel the screws are on the back of the machine.
10 Install is the reverse of the rip down

In hindsight I would have liked to have had the new part before I started the project because the wiring wasn't so fresh in my head a week later when it arrived even with diagrams. Over all it was very simple and took under two hours to complete. I did clean everything I could inside the machine and reglued a couple of the seals that had fallen loose. Works like new and probably went because of overheating with a clogged vent. Lesson... clean your dryer vent every year or sooner.

I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and li ... Read more miter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

I removed the gate in the back and found the belt had snapped. I continued to dismanlte the entire dryer to see what else was damaged. I pulled the drum out and ran the unit to make sure the motor didn't burn out and that the heater coil worked, which both did (I had no idea, this unit came with the house I purchased. They told me is was ... Read more broken.) So after finding the belt broken I saw that the top felt guide was rubbed down so far that the plastic guides where in paper thin, craked pieces.

I used the manuel that came with the felt guide to glue the new one on. If you do not replace the lower felt guide as well, make sure you mash the top felt down so that it's level with the lower felt. after I got my unit assembled the top guide pulled away because I didn't do this.
Installing the belt is timely, but easy. remove the drum then lay the belt around the visible line that the old one creates. Use this site's diagram to affix it to the pull and motor and that's that. Rotate the drum with your hand to even the belt out all around the drum to prevent it wobbling. I did this installation by myself, but it would have been much much easier if I had a set of hands on the other side of the unit.
Parts all fit together by either sheet screws or clips. Just keep track of which screw goes where. some are different sizes.

The repair was a bit more simple that what I had read here earlier, to see if I could handle it or I would have to call someone. The biggest relief was that I didn't have to remove any of the connectors from the control panel. Only 4 total connectors were removed at the Heating Element itself. Here's the steps I performed: 1) Pop the to ... Read more p off by prying the lid to release the 2 front clips and lift the top all the way up (like the hood of a car). Rest this against a door or wall. 2) Remove the rear access panel (2 phillips screws) on the bottom left of the unit. Remove the tension from the dryer belt and take it off the pully. 3) Go back to the front and remove (4 allen heads) from the back of the dryer drum. The drum should now have some play. 4) remove a plastic retainer that stops the drum from being lifted out. Now you should be able to lift out the drum. There is a ball & socket fitting that needs to come apart. This can be done by sharply lifting straight up. This gives you access to the heating element and you should be able to see where the coil has burned, thus opening the circuit. 5) remove (4 phillips screws) from the back panel of the dryer. Remove two pairs of connectors that attach to the heating element. Now it's out and you can begin the swap of the new element and reverse this process to put it back together. If I had to do this again, it would take less approx 30 minutes.

Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

1. I disconnected power cord
2. I used putty knife to loosen top by pressing into
the front spring clips holding it down and lifted the
front of the lid up against the back hinges and leaned
it back against a wall at the back of the machine.
3. Then I unscrewed the two screws at the top of the
i ... Read more nside of the front panel edges and unclipped the
wires from the door switch and then crimped the
metal clips holding the front panel to the main
body sides and then leaned the top of the front panel
toward the front and lifted it out and put it aside.
4. I then went to the back of the machine and undid the
two screws holding the motor area access panel and
took it off and put it aside. I then released the drum
belt tensioner and moved the belt away from the motor
pulley.
5. Then I removed the drum by lifting up on it so that the
ball axle could be pulled outward and then proceeded to
take the belt off and work the drum out of the front
panel opening and put it aside.
6. Once the drum was removed one could see the heating coil
assembly attached to the inside back of the dryer. One
needs to take off the two wires attached to the coil
spade connectors that are located at the ceramic
insulator. I decided to take out the whole assembly by
undoing the four screws at the outside back of the dryer.
7. Once the assembly is out of the dryer, then it becomes
necessary to remove the spade terminals from the
ceramic insulator, One must unbend the metal flanges
that have been bent at the base of the spade coneetors
at the surface of the insulator and then pull out the
spade connectors. Once this is done, then one can
unconnect the coil from the ceramic insulators holding it
to the assembly. Once the coil is disconnected one can
put in the new coil into the ceramic insulators, insert
the spade connedtors into the insulator, bend the
flanges to retain it and then reverse the disassembly
sequence for the assembly to complete the job.
Outcome,(I saved the old coil in case I need it in the
future.)
Outcome

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

1. Released the front latches under the dryer top and flipped it up.
2. Removed two screws holding the dryer front in place and flipped it down.
3. Tore off old drum glide and lower seal.
4. removed most of the remaining fuzz with sandpaper.
5. Glued the new seals in place.
6. Put everything back together.
... Read more r />All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.

Much cheaper than a new dryer!

Read less