F1253FDS3 (ASSEEUS) LG Washer - Instructions

1.open back of washer with screwdriver. 4 screws total. 2. Remove assembly with 17 mm socket. 3. Install new rotor assembly with socket. 4. Replace back of washer with sscrews. 15 minutes total time.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Opened rear compartment of washer and observed problem with drum shaft slipping inside of plastic motor assembly. The plastic teeth used to secure drum shaft were worn down. The part I needed was sent as an assembly but should have been sent separately for a much lower cost? The new part looked like it was of a sturdier design. All in all I saved hundreds of dollars repairing the washer my self. The woman I spoke to on the phone was really nice and very helpful.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

Disconnected power. Removed washer top, upper front control panel, and front panel. Removed hoses from washer drum housing. Removed cabling and support springs and stabilizers. Removed drum housing from cabinet. Removed bolts that secure the two halves of housing. Removed rotor from drum shaft. Removed stator from housing. Supported drum housing and with hammer and punch, removed drum shaft from bearings. Replaced bearings and seal and reassembled in reverse order.

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.

Tilt the unit back. Remove screws that hold the clean out. Disconnect the electric plugs and hoses. Remove pumps and housing. Change out pumps. Put back together reverse order

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!