F1253FDS3 (ASSEEUS) LG Washer - Instructions

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

First I had to elevate the washer on 3-5 gal. buckets in order to get underneath it and find the leak. Then I tried to repair the hose itself-which actually worked-but then the rest of the hose just started splitting everywhere I touched it. So I ordered the new part which took some careful comparing and examination online. But it was exactly the right part. You have to remove the top of the washer which is just 2 or 3 screws. Then taking the hose out was a little challenge-knowing I would have to put the new one back in carefully. Use Vaseline on rubber fitting at the end of the hose that connects to the washer. Need at least 2 people to raise the washer up in air to work on it.

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

Followed the video instructions provided.

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

Viewed two (2) on-line video's for bearing replacement. Produced a 40 item "punch list" as to action to perform following video. Followed sequencing of video's. Noted a 10mm and 17 mm socket needed, used 3/8 drive sockets. Also noted that a "deep Socket" of unspecified size used to aid in removal of nylon pins attaching (3) shock absorbers. Found that 1/2 inch sized (SAE) socket in my 1/2 inch drive socket set fit in the confined space nicely. Did not need the "deep sockets" (3 plus inch overall length) rather a normal sized 1/2 drive socket worked nicely to depress the nylon pin retainers. During reassemble replaced outer tub gasket, checked bolt torque six (6) times over 45 min. to assure complete seating.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

removed two screws from back of front load washer slid the top back two inches and pulled up removing the top.Turned the water off at the shut off . Used the pliers to remove the clamps on the hose to replace. Put the new hose on with new clamps. Un screwed the two screws holding the inlet valve and removed the hose and clamp. Put the new part in and put the hose and clamp back on then put the two screws back that hold the inlet valve.Total time to unpack the parts and install 7 minutes. All I did was google it on youtube and order the parts from this site which only took 2 days and tah dah .

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Basic skill

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.