6651598999 Kenmore Dishwasher - Instructions

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Took the bottom panel off and felt with fingers to replace spring with out pulling dishwasher out from enclosure.
Fairly simple

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Very easy to snap in. I would recommend to make them more slippery to snap in. Maybe use a little soap or place them in hot water before you place them on dishwasher tray.

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

Install too less that a minute. Fit perfectly.

My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.

Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure.
No leaks.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.