59650692000 Kenmore Refrigerator - Instructions

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Timer: Removed 2 screws from cover. Removed 2 screws to remove Timer. Installed new Timer & reassembled (15 min).
Thermostat: Removed screws from lower panel in the freezer. Removed thermostat from the cooling coil. Disconnected electrical connections. Had to cut 2 wires coming from fridge & install plastic piece provided. Ma ... Read more de up all electrical connections (1 hour).

simply removed old motor and replaced new. I'm over 82 and it was hard to get down and up to floor level!! One thing was a little puzeling -that was to insert the right screws which had a nitch in the end of the threds to keep it from loosening- I thought I was spoiling the threds cause I had to use a little pressure to start the screws ... Read more and thought I had the wrong screws--they had sent several sets of them for different name brands- but II got it and everything seems to be allright - Could you tell me if I could purchase a replacement compressor and some refrigerent -the new kind. thank you, George Erlandson Only if my comp. goes out!!!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector ... Read more was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Replaced the part--
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,

First I ordered the ice maker, but not the wiring harness...didn't fix the problem so I ordered a wiring harness, but ordered the wrong one...so I emailed parts select and got a prompt response on how to return the mistake and which part I actually needed. It was a "special order" but got in within days. Wonderful service!

Removed Ice bucket. Removed two screws and removed front cover from old ice bucket, two more screws under cover to remove ice agitator. Installed ice agitator to new ice bucket, installed two screws holding it. Installed ice bucket front cover on new ice bucket with two screws. Put new ice bucket into freezer. Finished! That was easy!

Had to disassemble ice maker to install part. . .

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was ava ... Read more ilable. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

Shipping was very fast, part easy to install.
The new filter head was redesigned making it easer to remove the filter.
Loosen the two screws and remove bracket.
Push in the tubing retainers and pull out the tubes.
Remove the two screws holding the filter on to the bracket.
Push tubing in to the fittings on the ne ... Read more w filter head, pull out the tubing retainers about 1/16 in.
Make sure tubing is pushed all the way to the bottom of the fitting.
Reinstall bracket and filter head.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Removed screws on back cover plate in Freezer, disconnected fan assembly, removed fan assembly, removed propeller from fan assembly, and transferred it to new motor, installed new assembly, reconnected electrical connections, screwed on back cover plate - Viola!