52750-5 General Electric Washer - Instructions

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

First of all to all you females out there, I am one and this is easy. It was a stacked washer/dryer and the dryer is gas. I unplugged the power, didn't unhook the gas and left them stacked, not a problem. Next I pushed in the 2 clips at the top with a small screwdriver while at the same time prying up on the top with my chisel, popped the top up and unplugged the wire bundle that's attached to the front panel. A few inches down on the inside of the front panel are 2 screws, I removed those. Then I pried the front panel off - there are 4 clips 2 on each side holding the front panel on. I pulled off the felt strips leaving a bunch of "hair". I read the other repair stories saying they'd wished that they'd used stronger solvent to remove the old glue and "hair" so I used laquer thinner and it worked great. Just saturate your rag and get the old felt and glue really wet and then come back with the chisel and the felt and most of the glue comes off and not the paint. I just kept going back over it with the saturated rag and chisel and it was pretty easy. I then put the glue on the felt strips, attached them, and used a ring of bungee cords to make a clamp around them 'til they dried. Put dryer back together and it works great. Also when you've got it apart - it's a good time to vacuum out the inside of the dryer.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Once the drum was removed it only took 10 min to remove and replace the coil. It took approx one hour to complete

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

I watched your video that explains the upper drum guide replacement. It was a piece of cake.

took the front panel off the dryer by lifting the lid and tilting it back and letting it hang there removed two screws from front panel at top right and left side and one clip fastener from left side of panel lifted the panel up and out took belt
off of motor pulley by opening back panel loosen belt tightner by pulling to the right takeing belt off motor pulley removed drum through front panel opening replaced drum bearing which is self explanitory changed heating element
by removing the power wiress from it removed the screws
from the back of dryer and replacd everything in reverse order WARNING MAKE SURE YOU DISCONNECT POWER I REPEAT MAKE SURE YOU DISCONNECT POWEr

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.

I watched the great easy to follow video from PartSelect. Absolutely nothing unclear. I was able to open the top and disconnect the front panel in less than 10 minutes! Removed the old felt drum glide, scraped off any stuck felt and loose glue. Then glued the new pad in place, using 3 small clamps, like clothes pins. Let it set for about 15 minutes then put it all back together! I did forget to reattach the ground wire, so I had to open the lid back up for that. About 50 minutes total. Also I took the opportunity of having the front panel off to give the inside a good vacuuming, not a ton of lint but enough to go ahead and clean it out! Thanks for the help!

Popped top off with flat head, took 2 screws out with phillips head, disconnected wiring, took front off, old piece removed, cleaned with razor blade, installed new glide, all done. I am sorry I waited so long to try this. So easy!

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.