52750-5 General Electric Washer - Instructions

loosened two hose clamps and four screws to replace the anti siphon valve.

Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.

i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.

Moved dryer out where I could get to all sides, then pulled top off, then unscrewed the front panel. The drum lifted out of it's ball bearing assembly in the back with a little force. Then it slid out fairly easy.

I replaced the rear bearing assembly, the bottom drum glide strip, the top drum glide and the vent seal all at the same time. The glue for the glide strips took about an hour to set up and I used clothes pins every 4-6 inches as suggested by someone else here on this site. Then I vaccuumed out the entire dryer body, vent pipes and every nook and cranny.

I put everything back as it had come out and then put the dryer back in it's place. Plugged it back in and it's as quiet as when it was new. Total time of project was about 1:45.

I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.

popped in one in

I watched the video you had. Did what the man said, checked out the parts, and orded the new ones. Then installed , as per video. It was Fun.

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

popped lid pulled front scraped old seal off ,good kit ,worked great. you guys are great 2nd day delivery,on parts for fridge ice maker solenoids and dryer parts. you got me for a customer from now on. thank you. steve

Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten each tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)

I ordered parts, recieved in 2 days. came with upper glide, glue and instructions. instructions were easy to read and follow. I used the wood chisel to remove old felt, cleaned well with some solvent, reap[plied glue, wait a few minutes , apply felt - reassemble dryer - viola- done. very satisfied customer

repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.