1985818201 Kenmore Freezer - Instructions

We turned off the water, removed the hot and cold water hoses from the machine, then unscrewed the metal plate on the back of our washer that was covering the water inlet valve. Next we removed the output hose and pulled out the inlet valve. As we unhooked each electrical wire we immediatley hooked it to the same location on the new inlet valve. Then we rehooked the out put hose and reversed our steps to finish the job. Before putting the plate cover back over the inlet valve we filled the machine with cold water and ran it through all cycles to make sure we didn't have any leaks. The pictures/insturctions that came with the new part were helpful.

This was the first repair job that our 20 year old Maytag washer has needed, and it was nice to be able to do the job ourselves. Reading other customers's repair stories on your web site helped us diagnose our problem. I found it easy to locate and order the right part and it arrived two days after being ordered.

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

First you turn off the main water supply or turn off the valves at the wall behind the washer unit. Second you disconnect the hot and cold water lines going to the washer unit valve. You then use 1/4 closed end wrench to remove one screw. Then you use a flat head screw driver to remove the two screws holding the valve in place. At this point use a 1/4 socket drive to loosen the clamp that is holding the hose that feeds water to the valve. Remove the hose. Then you disconnect the four wires and re-connect the wires to the new valve. Re-install the hose to the valve. Then you are ready to put it all back together.

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!

Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

Other guys have already spelled out in fine detail how to do the actual replacement. What I would add is this: First, I promised I wouldn’t swear during this repair. Second, I got everything I needed together including tools, a small bucket and some old newspaper to soak up the water that is sure to spill. I bought 6 foot stainless steel hoses to replace the old rubber ones. THIS IS HIGHLY RECOMMENDED as the last thing you need is a burst water line. Shorter hoses limit the distance you can move the washer without disconnecting them. The directions were wrong in that I did not need (nor could I use) the plastic sleeve over the outlet tube. So I very carefully had to pry this off without breaking the plastic bushing. And I had bent the clamp securing the outlet hose to the valve, and had a devil of a time getting it back on properly, so you may want to have a small tubing clamp handy as a replacement. Also, I checked for leaks before putting the valve back in place by holding it very carefully, powering up and turning the washer on and off a few times. Keep your fingers and sheet metal away from the terminals or your promise not to swear will be null and void! The last thing is that when I get into a project I go all the way, which meant pulling the washer all the way out and cleaning the floor and all the dust behind it, and even cleaning the washer itself. The result is my Maytag works like new, fills fast without the buzz and looks new, too. I love it when a plan comes together.

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

un hook electric and shut off water:
had to remove top of washer
remove two screws holding valve in place
un hook water line and elec. wires from valve
reverse to put new valve on
Billy Myers
Alamogordo,NM 88310

My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.

ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

After disconnecting the power and removing the input hose connections I was able to remove the valve assembly through the back panel. I then removed the wires from the valve and disconnected the outlet hose. I removed the old valve and replaced it with the new one. Then reattached the outlet hose and 4 wires to the new valve. The assembly then was reinserted into to the back panel and screwed into place. Reconnect the input hoses and plug it in and it's ready to be tested for leaks & used. (I had no leaks, BTW. A little silicone grease on the fittings made reassembly go easier but it's not needed. )